My ironing board is old. Well old for an ironing board anyway. I am still using my very first ironing board that I purchased nearly 30 years ago! Of course, the ironing board cover has been replaced many times over that 30+ years. An ironing board cover can only have so much iron-on interfacing glued to it before it needs to be replaced. And each time I replace the ironing board cover, I wonder if I should just replace the whole ironing board instead of just the cover.
I ask this because the cost of a nice cover is about the same as an new inexpensive board with a cover. The question I ask myself every time I buy a new cover is “Have ironing boards technically changed over the years and gotten better to where I am missing out on something by not buying a new board?”
So, this time when it was time to replace the cover, I decided to purchase a whole new ironing board and see if I have been missing out on anything over the years.
While standing in the middle of the isle of Walmartia, I found that I had three choices (i.e. three prices) to choose from. I decided to start at the lowest of the prices. I purchased the least expensive ironing board and took it home. Unfortunately, this ironing board was not inexpensive, it was cheap. To start, it only stood on two pole legs and it was very unsteady. It teetered this was and that every time I pushed my iron across the board. I had to keep catching it to keep it from falling over as I ironed.
The cover on this board was super thin with no padding at all and it was drawn tight around the board with a thin string and a clamp. The board itself was not a solid piece of metal either. It was a metal mesh desk with giant diamond holes in it with an attached outside edge. The diamond mesh was very bumpy to iron on, but the lip made by the attached edge caught the iron and interrupted the ironing process. Plus, this board had a very narrow tip end to the full size of the board, giving me less ironing space where I iron the most. This ironing board was certainly not a replacement for my current ironing board, so undaunted I tried again and back to the store I went!
This time I purchased the middle priced ironing board with higher hopes. It was just a little more expensive than a new cover for my old board was, and this ironing board had two legs in each direction, so I already knew it was going to be superior to the cheap ironing board I had previously purchased. It still had the diamond mesh board top, but I was hopeful that it would be made better and have a better cover, plus it had accessories. This ironing board had an iron holder at the end to give you more board to work on and keep the iron from tipping over when not in use. It also had a shelf on the legs.
This ironing board was certainly steadier than the last board and it did not fall over with the pressure of the iron moving back and forth, but the edge of the mesh top still had a lip. I might not have noticed the lip so much if once again, this ironing board did not have the same thin, non padded, tied on with string, cover that the cheap board had. If I kept this board I would immediately have to replace the cover. So, it was up to the accessories to “wow” me into replacing my old ironing board with this one.
I’m sorry to say, the accessories did not “wow” me. I am sure that for some, the shelf attached to the legs of the board is the greatest thing ever, but for me it was not. My ironing board has to be movable and with stuff stacked on the shelf, this board became unmovable. So, for me, the shelf would never be used. Plus, I don’t need another shelf to stack stuff on.
The next accessory was the iron holder. This holder is a great idea in keeping a hot iron from becoming a hot burn. But, what I found was that the holder created more work for me when ironing so I would never use it. When I iron, I mostly use the top half of the board, so I had to take extra walking steps to place the iron on the holder. It did not take long to tire of – iron, take two steps to set the iron on holder, take two steps back, move the garment, take two steps to pick up the iron, take two step back to the garment, and then repeat these steps. Simply put, my iron was not at arms reach, so if I kept this board I would not use the holder. Since the accessories did not work out for me, I saw no reason to replace my current ironing board with this board either.
Upon examining the highest price ironing board at Walmart, I found a duplicate of my current ironing board. Walmart had two styles of the this price ironing board. The first was the same diamond mesh board as the lower priced boards and there was no way I was purchasing that one even if the cover was thicker and nicer because of the previous issues with the mesh boards. The second board looked just like the ironing board I currently have at home in the sewing room, except that the cover was not as nice. So, why spend the money for a new ironing board when it was exactly what I already had?
I guess nothing new and revolutionary has occurred over the years to improve the ironing board. With my new knowledge of ironing boards, I decided I would be keep my same old ironing board and replacing the cover.
As I looked at new ironing board covers, I learned that they are the same as new ironing boards. You get what you pay for with the lowest price covers being thin, non padded and string tightened and the higher prices ones being thicker, padded and velcroed on. With what I had learned from my ironing board experiment, I went ahead and purchased the higher priced, thicker, padded, velcroed cover. The new cover fits my old ironing board great and I am back to ironing on my latest sewing project. Stay tuned to see it soon!
Until then, sew forth and iron on!