Archives

It’s In The Bag! – Part 2 – The Lining

DSCN3886After completing the shell, I sewed the lining next. I serged all the seams and edges of the lining because the gray lining fabric just loved to fray. This was not difficult, just time consuming. I left part of one of the sleeve seams unstitched for the bagging of the jacket. With the shell and the lining sewn, it was time to sew these together and bag the jacket.

DSCN3880Even though I knew what do sew next, I decided to read the tutorial for bagging a jacket one more time, and I am glad that I did. At the top of the bagging tutorial was a link to a tutorial on how to cut a lining for a jacket. I had not read this tutorial before and even though my lining was cut and sewn, I decided to read the tutorial.

I was unpleasantly surprised to find out that I had made my lining incorrectly. There were more steps to cutting a lining out than just cutting out the pattern pieces again from lining fabric. I debated about just using my finishing lining and learning the lesson for the next time but then I read how if the lining is not cut with ease, the jacket will not fit or wear well.

Darn!

DSCN3909I was going to have to make another lining! And this time I would be following the tutorial to get it right!

DSCN3890I returned to the cutting table and I cut out a new lining with the extra inches at the fold in the back and the ease at the armscye and sleeves. I once again cut the lining 2 inches shorter at the bottom and at the sleeve’s hem. At the sewing machine, I made a box pleat in the top and bottom of the back piece to gather in the extra inches. I once again serged all the seams and edges to keep the lining fabric from fraying, and I once again left part on one of the sleeve seams open for the bagging. With a whole new lining, one that had appropriate ease added in, I was ready to once again bag the jacket.

DSCN3892Following the steps of the bagging tutorial, I sewed the shell and lining together. Next I sewed the sleeve hems together, and then turned the jacket through the unfinished seam on the sleeve. This worked fantastically! The zipper turned beautifully to the front of the jacket, the collar was finished, with no twill tape or facing needed, and the hems both at the bottom and sleeves rolled up 1 inch. The last step was to sew the unfinished seam of the sleeve together.

DSCN4004Normally, this is where the hand sewing would be required, but the tutorial said just to sew along the edge of the sleeve seam with wrong sides facing. Yes, this left a little ridge, but it would be inside the sleeve where no one would know that it was there, or see it, or even notice it while wearing the jacket. Even with the jacket off, it would be highly unlikely that the sleeve would ever be turned inside out to reveal this seam. This was great for me! A quick easy seam to finish the jacket plus no evil hand sewing!

DSCN4007As I zipped my completed jacket up, I figured out why the making of the lining tutorial kept talking about the facings. I assumed that since I was lining the jacket, the facings were not needed, but after zipping the jacket and having the lining exposed where the facing would have been, I could see how the facings from the shell fabric would look and wear better than the lining.

DSCN4000At this point in the construction I did something I don’t normally do when I am sewing kid’s clothes. I needed to remove the top stabilizer that I had used to hold the fleece down while embroidering on the pockets. I could have just ran a little water over the pockets and let them air dry, but I decided to wash and dry the whole finished jacket instead, just like a mom would do after the kid had spilled ice cream down the front of it.

DSCN3992I was a little disappointed when I removed the jacket from the dryer. The fleece had fuzzed up a little and some of the shiny new look was gone, but all the seams held well and the lining did just fine. So at least I know this is not a dry clean only type of situation, which wouldn’t be good on a child’s garment, and that the jacket can be machine washed and dried without ruining it.

DSCN3990Despite the exposed facing and the fuzzing fleece, this jacket turned out just too cute. I love the paw print, the contrasting colors, the side patch pockets, the Dalmatian embroidery designs, the zipper and the lining.

Let’s face it, I love the whole jacket! I especially love the bagging of this jacket and the lack of hand sewing. I see another jacket just like this one but with facings added in my near future, so stay tuned!

Until then, sew forth and bag on!

Advertisements

It’s In The Bag! – Part 1 – The Pockets

DSCN3898I found one more way to finish the edges of polar fleece seams on a jacket. Just put a lining in the jacket! Now, lining a project has always frightened me just a little because it required hand sewing to finish it up and as you know hand sewing is evil and must be avoided at all costs. But, I found a great tutorial online explaining how to bag a jacket, i.e. how to add a lining to a jacket, with little to no hand sewing so I was excited to try bagging a jacket for the first time.

At the top of the tutorial, the statement was made that any garment could be lined regardless of whether the pattern called for a lining or not, so I did not bother to look for a pattern with a lining. I just grabbed my tried and true kid’s jacket pattern, Simplicity 8902. It took only a minute to pick out the red puppy paw print fleece fabric and some gray lining to use to bag this jacket.

DSCN3873I gave the design and construction of this jacket a lot of thought before I made the first cut into the fabric. I decided I did not need the facings on it since the lining would replace them. Next, I would cut the lining 2 inches shorter at the hems of both the bottom and the sleeves so that the lining would pull the fleece around to complete the hems. Last, I wanted to embroidery a design on the jacket, but I knew that it would get lost in the busy puppy paw design of the fleece.

DSCN3874So to remedy this problem, I decided to make side patch pockets for the jacket from some grey fleece scraps and to embroider the designs on to the pockets. I also decided to make the collar from the grey fleece too to match the pockets. I thought about using the lining fabric for the bottom of the collar, but the grey fleece was not that heavy so I decided to make both sides of the collar using the fleece. With that plan in mind, it was time to cut the fabric and get sewing!

DSCN3876The cutting process went smoothly. I cut out the pieces for the shell or outside of the jacket from the fleece and then I cut matching pieces from the grey lining. I started the sewing process with the shell of the jacket which was going along just fine, including the sewing on of the zipper, until the pockets.

DSCN3879The husband picked out the Disney 101 Dalmatians for the embroidery designs so I embroidered Perdita on one pocket and Pongo on the other. With the embroidery done, I decided I wanted to line the pockets to protect the back of the embroidery designs from things that would be put in the pockets and to protect little hands from the embroidery designs rough parts. But, how should I line the side patch pockets?

DSCN3991To line the pockets, I cut two pockets from the lining fabric minus the fold over flap. I serged the edge of the lining fabric where the flap would have been. I folded the fleece flap of the pocket to the wrong side of the pocket and then placed the lining on top. I then sewed right sides together on three sides of the pocket. Next, I turned the pocket at the flap. After ironing the pocket, I folded the flap over, encasing the exposed but serged lining under the flap, and then I sewed the flap down to the pocket to complete the lining of the pocket. It was then simple to sew the pockets onto the front shell of the jacket.

I am going to pause here and let you catch your breath for a minute. I still have a lot of story to tell about the sewing of this jacket. So, stay tuned for the exciting conclusion in part 2 of It’s In the Bag.

Until then, sew forth and bag on!

 

Applying The Lessons Learned

IMG_0016After being so pleased with the construction process of the dinosaur vest, and then so flustered by the construction of the ant jar vest, I wanted to make another vest. And in the process I wanted to apply the lessons that I had learned and to end the vest making process on a more positive note.

So, I grabbed some more bottom weight scraps from my pile and some monkey printed flannel and I got started! As I laid out the fabric to cut, I spied some pleather that I had waiting to make its way it to the stash. Oh yes! I would give this vest a pleather collar and welt pleather pockets to step up the style!

DSCN3956With the design completed, I started to cut out the fabric. Because I was working with scraps, I did not have a single piece big enough to cut the back of the vest on the fold, so I would need to add a back seam to this vest. A back seam would not affect the wear or the construction of the vest so I saw no problems in having a back seam. Applying the lessons learned from the previous vest constructions, I remembered to cut the extra inch for the buttons on the fronts of both the top fabric and the lining. I also remembered that I wanted to add some interfacing to the pleather the next time I used it. Soon, I had all the pieces cut out, interfaced, and I was ready to start sewing.

DSCN3957The first step in the sewing process was the embroidering of the monkey design. Remembering the lessons learned from before about placement, I thought long and hard about the placement of the embroidery design versus the size of the design and the collar before I finally hooped the fabric and stitched the design. When the design was completed, I saw that I was not going to have an issue with the collar covering the design. If fact, I had over compensated and I was wishing that the design was a little higher than it was. Even though, the monkey design is the best placed embroidery design I have done on these vests, I still have a few placement lessons left to learn.

DSCN3700The next step was to sew the pleather welted pockets. As I debated about the placement of the welts, the husband peaked over my shoulder to see what I was doing. When I showed him the pleather welts, he said no, that I should make patch pockets like on the dinosaur vest from the pleather. I explained to him that I already had the welt pockets cut out and interfacing applied to the pleather welts, but he insisted that I should cut new patch pockets from the pleather instead. Since I know that the husband has a good eye for design I followed his lead and cut out some new patch pockets from the pleather and sewed them on the front of the vest. The pockets came out great! The pleather was easy to sew and the pockets look very good on the front of the vest. Plus, the monkey embroidery design sits at the top of the pockets so it is now not too low.

DSCN3702When it came to the pleather collar and the pockets, I remembered lessons learned about using a press cloth to iron the pleather. I top stitched the edge of the collar so that it would match the stitching on the pleather patch pockets. The rest of the sewing process went smoothly, even the stitch in the ditch seam of the band.

When it came time for the buttons and buttonholes, I applied the lessons learned from the previous vest’s buttons and buttonholes. I decided not to have a button at the top of the vest, but to place the first button so the vest was open as I expected the vest to be worn. I then spaced the other buttons appropriately. The buttons looked like they were in the right place and there was no seam issues when sewing the buttonholes.

DSCN3963I am super pleased with the end results of this vest! It is just adorable!

And as much as I hate to say it, the husband was right and I just love the pleather patch pockets!

The pleather patch pockets are just perfect with the monkey embroidery design and the pleather collar.

Plus, I am super pleased with myself for remembering and applying the lessons learned from previous sewing projects.

I hope some little girl will enjoy wearing this vest as much as I have enjoyed making it. With the success of this vest, I am ready to more on from vest construction to other sewing projects, but I will happily make more vests at anytime.

Until then, sew forth and apply your lessons learned on!

Some Lessons Learned For Next Time – Part 2

Continuing on with the sewing of the denim ants in a jar vest…

DSCN3525The next step in the sewing process was to add the pockets. Since I really did not have a pattern for the side seam pockets, I decided I would design and sew them how I wanted. In designing the pockets, I wanted the fun flannel I was using to make the pockets to show, so I decided to cut a rectangle from the sides of the jacket fronts. But, how big should I cut the rectangle? After some thought, I cut the rectangle what I thought the size should be, 5 inches tall by 1 inch deep, and then cut the pockets to match. With this size of square, I would place the pocket 1.5 inches from the bottom of the fronts.

DSCN3524In the sewing process, I noticed right away that I had a good size opening for the pockets but not much depth to the pockets. I should have cut the opening square shorter and used that extra length for the pocket depth. It was too late now though as the fabric was already cut. So, the finished pockets are very cute and the flannel is showing, and the pockets will certainly keep the wearer’s hands warm but the pockets won’t be too useful for hold many items due to their short depth. Another lesson learned for the next time!

DSCN3530The next step was to add the bottom band which was a little difficult due to the stiffness and weight of the denim. I had to use a little liquid stitch to help hold the denim in place to start and stop the stitch in the ditch seam. There was a lot of bulk from the denim front, the seam allowance from attaching the band, and the folded over finish of the band, i.e. 5 layers, in this seam. I trimmed the seam allowance but it was still bulky and difficult for my sewing machine to get started on this final band seam, but I made it through it ok.

DSCN3531The final step was to add the buttons. I measured evenly to place the buttons, but when it came to sewing them on, I had to move the top button down slightly due to the bulky denim seam at the top of the vest. This left the buttons mis-spaced slightly. The top button is not quite high enough to keep the vest closed around the neck if it is worn closed. If the top button is left undone, the vest opens a little too much before the next button. This could have been avoided by sewing horizontal buttonholes and avoiding the DSCN3928 (1)bulky denim seam at the top, but because of the pieced strip on the front of the vest to add the extra inch, I had to make the buttonholes vertical. If I had given the placement of the buttons versus the bulky denim seams a little more thought before I started to sew, I could have placed the buttons better. Another lesson learned for next time!

Now that the vest is complete, I am pleased with the end results. I also think the vest will wear just fine, and I hope some kid will enjoy wearing it too. Many lessons were learned from the making of this vest and I hope to remember all these lessons and apply the lessons to my future sewing projects.

Until then, sew forth and button on!

Some Lessons Learned For Next Time – Part 1

DSCN3928 (2)My latest sewing project was destined to be yet another learning experience for me.

After the successful sewing of the dinosaur vest, I wanted to make another vest. When I made the dinosaur vest, I had envisioned so many different options and fabrics for these vests, so this made it easy to decide that my next sewing project would be to make some of these vest options a reality!

The designing of this vest was not difficult at all. When I was picking out the fabric for the dinosaur vest, I had also pulled out a denim scrap that was just big enough to make a vest and a greenish blue flannel with yellow bug outlines from the stash. I could see a vest from these two pieces of fabric and I knew that I would sew one of my favorite embroidery designs, some ants escaping from a glass jar, on the front. Because of the large size of the embroidery design, I would give this vest side seam pockets rather than patch pockets.

With the design of the vest all outlined, it was time to cut it out and get sewing!
DSCN3931 (1)When I laid out the pattern pieces of Simplicity 8902, on the denim fabric, I remembered that I needed to add an inch to each front for the button overlap. I carefully laid the pattern pieces out correctly to cut the extra inch, but then I promptly cut along the edge of the pattern piece as shown on the pattern and I did not add the extra inch. How dumb was that? Well it was done now and I couldnt undo it so I decided it was a lesson to be learned for the next time I make this pattern.

The denim scrap that I had was not big enough to cut two new fronts, so instead I cut two 1.5 inch strips of the denim to add to the fronts of the vest. The strip would look like an intended button placket rather than a fix, so all was good despite the cutting error that I made. After cutting out all the pieces and remembering to add the extra inch to the front of the lining, it was time to being sewing.

DSCN3930 (1)The sewing process started with embroidering the design to the front of the jacket. I remembered that I wanted to do the embroidering first before adding the pockets to keep the pockets out of the way of the embroidery. I also remembered that I wanted to move the embroidery design down so that there would not be an issue with the collar covering some of the design.

What I had forgotten was that the ants embroidery design is two inches taller than the dinosaur design and I did not remember to take that into account when positioning the design. So, even though I moved the design down on the vest, the top of the design was still higher than I wanted it due to the extra height of the design. After stitching the design to the front of the vest, I realized that the top of the ant design was still going to be under the collar, and not just at the edge of the collar like the dinosaur design but that the ant at the top was going to be under the collar. That will be another lesson learned for next time I use this design!

DSCN3932 (1)Flustered even more, I now had to come up with a solution to fix the collar/embroidery design problem. I thought about making this vest collarless or adding a standing ribbing collar that would not fold over, but I did not like the look of these options.

I decided to see if I could just shorten the collar enough so that it would not cover the ants but it would still fold over and look ok. To do that I cut over an inch ff the bottom of the collar. The collar looks a little small now that it is done, but it works just fine. The collar lays right at the edge of the top ant’s antenna, and with a little encouragement, the stiff denim will fold over just enough to cover the collar seam. Still not being totally pleased with the collar, I continued on with the sewing process to the next steps.

But that’s a story for next time.

Until then, sew forth and ant on!

Oh! That’s Gonna Leave a Welt… – Part 1

DSCN0977I decided that is was time to try making welt pockets.

Welt pockets always look so nice and professional, plus I had something special I wanted to try for the welts. One day while shopping at Walmart, I saw a couple of bolts of patterned pleather and I knew right away that it would be perfect to make the welts for the welt pockets from. I quickly purchased some, and headed for my sewing room.

First, I needed a pattern. After looking through my pattern stash, I turned to my Kwik Sew books on the shelf.

Yes, there were jacket patterns with welt pockets and instructions in these books. I was super excited and ready to get started!

Next, I had to choose a fabric for the jacket. I had a bright yellow sweatshirt fleece hiding in the stash and debated if pleather and sweatshirt fleece would look good together. I finally decided that they would, especially for a first try of welt pockets. It was easy to pick out some left over scraps from one of my shirts for the body of the pockets.

DSCN0827DSCN0830And I decided to make a size 8 jacket because of the length of the zipper I had. I would need to lengthen the jacket a little to accommodate the zipper, but I didn’t think that would affect the wearing of the jacket.

The first step in making this jacket was to see if pleather would survive the washer and dryer.

It did! And beautifully I might add!

The next step was to see if my sewing machine would sew the pleather or if I was going to require a special foot, needle and thread for sewing the pleather. I did not. The pleather sewed beautifully with just my normal pressure foot, regulars thread and a new Schmit universal needle.

DSCN0833DSCN0836Wow! I had read horror stories on the internet about sewing with leather but I guess pleather is different, or maybe just these particular pieces. Regardless, I was excited!

With the pattern traced and the fabric cut, it was time to get sewing.

To sew the welt pockets, I started with some scraps to get an idea of what I was doing, then I moved on to the jacket.

DSCN0838DSCN0842I started by applying a pieces of interfacing with the sewing lines to the front of the jacket. Next, I taped the pleather in place and then O sewed around the lines.. I taped it because I did not want to scar the pleather with pins. Cutting was next and then pulling the pleather to the wrong side to form the hole for the pocket. Then I folded up the welt and sewed it in place, and then I attached the body of the pocket to the pleather and finally I sewed around the body of the pockets.

DSCN0848DSCN0844Soon enough, I had completed the two welt pockets. They are not perfect but they were fun to make and I really like the results especially with the pleather.

I debated about interfacing the pleather of the welt but I thought that the pleather was stiff enough to not need interfacing. As I inserted my hand into the pocket, past the welt, I wished that I had interfaced the welt and made it stiffer to withstand use over time.

I had pictured the welts as being bigger than they finished up being. Knowing now how to make welt pockets, I feel that I can make the welts in different sizes and styles the next time I make something with welt pockets.

Coming up next, the completing of the jacket.

Until then, sew forth and welt on!

Girl’s Fleece Jacket (Done Backwards) – Part 2

DSCN2088When I started this jacket, I decided to go ahead add the optional cuffs to the sleeves.

The cuffs looked so cute on the jacket on the pattern envelope, that I wanted this jacket to have the cuffs. But when it came time to sew the cuffs on, they were not turning out very well. They were just too bulky. The cuffs are made from two pieces of fleece. The first piece is sewn to the sleeve, then the next piece is sewn to the first piece and then folded over to make the cuff. I cut out the cuffs, sewed the cuffs to the sleeves and then removed the cuffs. In my opinion, this was a bad design for a fleece cuff due to so many seams in the cuffs and the bulkiness these seams caused. There are four layers of fleece in the top seam of the cuff, and that is just too many layers of fleece.

DSCN2084If I wanted to keep the cuffs, I had to come with a solution, so I gave it some thought and came up with some ideas.

First, the sleeves could be cut longer to make the cuffs. This would eliminating the bulky seams, but I had not cut my sleeves longer so this solution was out for this particular jacket. Another solution would be to use a thin lining fabric as part of the DSCN2086cuff, but I did not have it in me to dig through the stash to find a matching fabric. My third solution was to skip the cuffs, and make more bias tape. I would finish the edges of the sleeves with yellow bias tape to match the pockets. (My first thought was to use the bias tape to finish the edge of the cuffs, but eliminating only one of the layers in the bulky cuff was not enough.) So, I choose this as my plan. This jacket would not have cuffs, and I would finish the sleeves edges with the yellow bias tape.

Thinking back, I could have had cuffs on this jacket by combining the solutions. I could have used a lining fabric and the bias tape to make the cuffs and eliminate the bulk. Hmmm. Maybe I will try that on the next jacket.

DSCN3414By using the bias tape on the sleeves, I did not have to worry about a hem or the fact I had not cut the sleeves longer to accommodate a hem. I applied the bias tape to the edges of the sleeves, trimmed the seams and turned the bias tape to finish the seams. I noticed that the thin bias tape looked weak at the bottom of the heavy sleeves. The way I got rid of this weak look was to not trim the seam inside the bias tape so much, which was different from any other time I have applied bias tape. Previously, when I applied bias tape, I wanted the seam allowance trimmed out before folding the tape over. If the seam allowance was left inside the bias tape this time, the look was much fuller and it looked better.

DSCN3418It was now decision time. Which way did I want the jacket to cross, left over right or right over left? After a lot of thought and debating, I decided to cross the fronts as if it were a boy’s jacket, the left front on top of the right front. This will probably drive the little girl that wears this jacket nuts as she tries to button the jacket backwards, but the half froggy’s that I got from folding the jacket the other way just didn’t look good. Hopefully whoever wears this jacket won’t mind the backwards buttoning buttons if it is a girl.

I was dreading making the buttonholes on this jacket. I was not sure how my sewing machine would handle sewing buttonholes on fleece. Sometimes, even with thin non-stretch fabric, my sewing machine has a mind of its own when it comes to making buttonholes and sews whatever it wants to. To help combat this problem, I made horizontal buttonholes, and held my breath as the buttonholes were sewn, but my sewing machine did great and the buttonholes turned out just fine.

DSCN3413If I had known then, at the beginning of the sewing of this jacket, what I know now, nearing the end of the sewing of the jacket, I would have added piping to the peter pan collar to coordinate with the finished design of jacket. It would have been really cute to have had the bright yellow piping around the collar to match the piping on the pockets and the bias tape on the sleeve. This is definitely something I will keep in mind for the next jacket.

DSCN3416With the sewing on of the last button, the jacket was finally done!

The making of this jacket was a learning experience from the beginning to the end, from the cutting of the fleece, to the sewing of a back facing, to the piping curved pockets to the designing of the fleece cuffs. There were many lessons learned on this fleece jacket.

All in all, I think the jacket is very cute and I hope some little girl will be willing to wear it and will enjoy it!

Until next time, sew forth and fleece on!