Archives

Don’t Panic – Part 2 of Sew it Begins.

Although I worked on both the husband’s new shirt and my new shirt at the same time, the husband’s shirt was the first one completed.

The husband picked a purple single knit with quite a bit of stretch from the stash for his shirt. I was not excited about getting back into the sewing grove with a stretchy knit that could possible give me grief, but what sewing project doesn’t present itself without certain challenges. This stretchy knit would certainly sharpen my dull sewing skills quickly. I had plenty of this fabric to work with so the shirt would be entirely made from this fabric, instead of piecing it together as my last few had been.

After laundering the fabric and cutting out the pattern pieces, it was time to interface the collar and the yoke. I picked a nice piece of interfacing and ironed a small sample piece onto a scrap of the purple knit. It ironed on great, but when I stretched the knit, the interfacing disintegrated and shredded to pieces. After that disappointment I started cutting samples from other pieces of interfacing and ironing them to the knit. Some were better than others but none were what I wanted. I wanted an interfacing that would stop the knit from stretching and make the collar stay formed but not too stiff.

Was I expecting too much from the interfacing?

I tried all different kinds of interfacing, woven, non woven, knit, and so on and I finally found one that I thought would work and hold up well with the stretch. I cut out the interfacing for the collar only to find that I did not have enough of this interfacing for the yokes. So, off to the store I went. I picked out what I thought was the same interfacing, but it was not. I studied the interfacing from the stash again and settled on one that was acceptable. You know, I just don’t understand interfacing. I have done research and read up on interfacing several times and purchased a wide variety of interfacings and tried them all, but I still have trouble when it comes to choosing and using the right interfacing for a project. Trial and error is the only answer I have come up with for my interfacing dilemma.

With the pieces of the shirt cut and interfaced, I started to sew. I was very careful and cautious with the knit, watching the stretch with each seam. The hems, of course, were the most tricky part with the stretch but with care, it all came out good. And yes, this knit shirt did a great job of sharpening my sewing skills.

When it came time for an embroidery design, the husband picked the “Don’t Panic!” design from the Hitch Hikers Guide to the Galaxy. I knew this design would look good on the purple shirt but when I was done stitching the design, it looked great. After sewing the buttonholes and the buttons on, the shirt was done.

The husband likes his new shirt and I love being back in the sewing studio, sewing away.

Stay tuned for details about my new shirt in my next post.

Until then, sew forth and Don’t Panic on!

Star Wars Senior

DSCN4060DSCN4067“They won’t fit.” That is the reply I got from the husband when I showed him my latest sewing project, the kid’s Star Wars sweatshirts. What do you mean they won’t fit? These shirts will fit a 2 year old just fine. Then, it dawned on me. These shirts would not fit the green eyed husband. So, my next sewing project would be a Star Wars shirt for the husband.

 

Looking at my Star Wars embroidery designs, I picked a maroon colored knit from the stash for the husbands shirt. After laundering the fabric, I laid it out on the cutting table to get started only to find out that the maroon fabric was not big enough to make a shirt for the husband a shirt from it. So, the husband picked a black knit from the stash for the sleeves and the collar. As I cut out the fabric, I was glad that I did not have enough of the maroon fabric. The black and maroon fabrics looked really good together. Far better than the maroon would have looked alone.

 

DSCN4044DSCN4043It’s been awhile since I have made the husband a new shirt, but the sewing process went smoothly enough. Both the maroon and black knit fabric are nice fabrics and where easy to work with. The husband picked his embroidery design, the Stormtrooper with the sun ray rising sun background, and it embroidered on to the shirt nicely.

 

All was going along nicely until the husband picked white/clear buttons and white thread for the double needle hems on the bottom of the shirt and the sleeves. I was more then a little apprehensive about this. Sometimes when using a double needle, my sewing machine and the knit fabric that I’m DSCN4065DSCN4063sewing with like to argue during the sewing process. I can hide a lot of this arguing with a matching thread color but could I hide the arguing with a white contrasting thread?

 

Luckily, as I mentioned before, these were nice knit fabrics to work with and they did not argue with the double needle and the hems sewed fairly smoothly and they look good.

Finally with the last step of sewing the buttons on, the husband’s Star Wars shirt was done!

 

DSCN4041DSCN4042But before I could go back to sewing some more kid’s Star Wars clothes, the husband pointed out the Chewbacca fleece blanket kit we purchased at Joann’s last half price sale. After the husband gave me some sweet puppy dog eyes that said “Please make my blanket next”, I got started on his blanket.

 

To increase the size of the blanket, I did not cut off the black dotted line edges of the blanket that were supposed to be cut into strips and then tied together. Instead I squared the top and bottom fleece pieces and then sewed them wrong side together 1/8 inch from the edge. Next I cut 1/4 inches from the edge with the skip stitch blade. The blanket was then ready for its edge to be crocheted on.

 

DSCN4035DSCN4038After crocheting the foundation row, I tried several different edges like scallops and triangles but the husband liked the chained edge the best. So I chained 3, skipped 2 stitches on the foundation row, then slip stitched in the 3rd stitch. On the next row, after changing colors, I chained 3 then slip stitched in the next chain 3 of the 2nd row. For the 3rd row, I picked a different color but I didn’t like the multicolor look so I changed back to the foundation rows color and crocheted the 3rd row like the 2nd row. I had planned to crochet a 4th and 5th row, but this did not look good so I stopped after the 3rd row.

 

The husband was pleased with his finished Chewbacca blanket as well as his new Stormtrooper shirt. Both were fun for me to sew and crochet. Now, that the green eyed monster has left the sewing room. I can get back to sewing more kid’s clothes.

Until then, sew and crochet forth and remember to always let the Wookiee win!

Creative Determining – Part 2

DSCN3986DSCN3987To begin the the sewing process of the Snoopy peplum top I started with the peplum first.

Since I was not going to line the peplum, I wanted to hide all the seams as much as possible, so I sewed French seams to piece the peplum together.

 

This was not difficult, just time consuming with a lot of ironing in between seams. I did a simple 1/2 inch hem at the bottom of the peplum to complete it.

Sewing the bodice was next. I decided at the last minute to add the yellow sleeves to the top. I like the yellow sleeves but as I snipped the curve of one of the sleeves I caught the lining and so I had to do a little mending. Luckily, the mended spot is on the inside of the top and cannot be seen from the outside. It should not affect the wearing of the top.

DSCN3998DSCN3989After gathering the peplum, I sewed the peplum to the bodice, making sure to line up the seams as much as possible. I serged this seam to finish it, rather than covering the seam with the lining and doing the stitch in the ditch seam.

The serged seam looks fine and saved me the headache of doing the stitch in the ditch seam.

 

I probably could have used the practice sewing the stitch in the ditch seam on this top, but sometimes just sewing the easy and simple way is fun too. And it’s much less stressful too!

With that, the little girl’s peplum top from the leftover Snoopy fabric scraps was completed!

DSCN3995DSCN3994The top is just adorable and the multiple seams in the peplum are really not that noticeable with the gathers.

This was a fun sew.

It is always fun to make something from nothing and to let the creative side flow to make it work.

Unfortunately, now that I have used up all the Snoopy scraps, I have at least a hundred projects that have raced through my mind that I could have made using the scraps.

Having said that though, I am not disappointed at all that I used these Snoopy scraps to make this top and at least they were put to good use!

Until then, sew forth and determine on!

Creative Determining – Part 1

DSCN3986There was no way that I was going to throw away any of the precious Snoopy fabric scraps left over from my new Snoopy shirt. The scraps really were not large enough to make anything with, not even for a child, but I just could not bear to throw them away. So, what to do with these scraps beside stack them on the edge of the cutting table and stare at them?

Recently, I have seen several little girls peplum tops that are just adorable and I have wanted to make one. So, looking at the Snoopy fabric scraps, I decided to see if I could squeeze a little girl’s peplum top out of the pieces. The size of top I would make would be determined by the dimensions of the scraps.

DSCN3813I didn’t really have a pattern so I turned to the internet for ideas. The first style of peplum top I found had a circular peplum. This was out of the question. The scraps I had to work with were absolutely too small to cut a circular peplum from. The second style I found was a gathered peplum. Hmmm. I might be able to make this work with the scraps.

DSCN3985Now, how long should the peplum be versus the length of the bodice? I saw a variety of bodice and peplum lengths from long bodices with short peplums to short bodices with long peplums and many hi/low peplums in between while I was searching. Once again, I would need to let the dimensions of the scraps determine the length of the peplum and the bodice and the scraps would also determine how full the gathered peplum would be.

DSCN3999Still not having a pattern, I pulled out my favorite little girls dress pattern as a guide. Based on the size of the largest scrap, I determined that I could get a size 4 bodice front and back from the scraps as well as have a few pieces left over for the peplum. I quickly picked some yellow cotton from the stash that matched Woodstock for the lining of the bodice.

To make the peplum, I squared the remaining scraps of Snoopy fabric I had and found that I had two pieces approximately 6 inches tall by 12 inches wide and 4 pieces that were 6 inches tall by 6 inches wide. (Actually, one of the 6 by 6 inches pieces was only DSCN39965 inches wide, but I could work with that.) With a lot of seam work, I determined that I could make these scraps work out for the peplum. I would sew the two 12 wide pieces together for the front of the peplum and sew the 6 inches pieces together for the back or the peplum.

I would not be matching any of the designs in the Snoopy fabric. There was certainly not enough scraps for that, but luckily with a gathered peplum, the non-matching designs as well as the many seams that I would be sewing would just be gathered in.

Excitement for this project grew, as I saw my almost useless scraps become a little girls peplum top!

Stay tuned for the sewing of the little girl’s Snoopy peplum top.

Until then, sew forth and scrap on!

Down In The Southwest

DSCN4029Waste not, want not, but as you know there is more to it when it comes to fabric scraps and remnants. It’s the challenge of making something from nothing and the creativity of making it work that gets you to use those scraps and to buy those fabric remnants from the bargain bin at the fabric store.

It was this challenge and creativity that got me to begin my latest sewing project.

DSCN4027I saw this southwest print in a stack of discounted flat fold fabrics and I just fell in love with it. I love the bright colors on the black background and the fabric has a nice weight and feel to it. But, there was just a little over a yard left. What could I make from that? The fabric would be ideal for me a shirt, but could I figure out how to piece it together with other pieces of fabric to make me a shirt? Color blocking ideas swirled in my head so I quickly purchased the piece of southwest print fabric and brought it home!

DSCN4033With a color blocking design in mind, I dug through the stash and found several pieces of fabric that I could put together with the southwest print to make me a shirt, but the deep blood red piece that I found was by far my favorite. But, as I went to cut the shirt out, I noticed that the red piece of fabric was terribly flawed.

What was such a flawed piece of fabric even doing in the stash?

I returned to the stash to select a different piece of fabric to use with the southwest print but now I did not like any of my other choices. I thought about going back to the fabric store to look for more red fabric but I was too disappointed to go. I took another look at the flaws in the red fabric to see if I could work around them. How could I make it work the way it was? After much thought, I came up with a new color block design that should work, but I would have to cut the southwest print perpendicular to the grain line.

Would it be ok to cut against the grain?

DSCN4022After much studying and reading about grain lines, grain, cross grain, welt and warp threads, I decided that yes it would be ok to cut my fabric perpendicular to the grain line as long as I was careful to cut on the cross grain just as I would be careful to cut on the grain line. At this point after fully researching the issue, it was finally time to cut the fabric.

The cutting process started with tracing my pattern and then cutting out new pieces for the color blocking. This took time and thought. I had to decide where I wanted the seams to be, add some seam allowances and then reshape the armscye and hem. With the new pattern pieces created, it was time to cut. I carefully cut the front and back pieces perpendicular to the grain line from the southwest print and the I carefully placed and cut my new side pattern pieces and sleeves around the flaws of the red pieces of fabric. With the pieces all cut out, it was time to sew.

DSCN4023The sewing process was going along smoothly until I noticed the flaw of the red fabric in the center of one of the sleeves. I thought I had cut so carefully around the flaws but I guess that I had not. I had no more non-flawed red fabric to cut out another sleeve with. Could I just pretend the flaw was not there? No, I would never wear the shirt with the flawed sleeve. Hmm, I wondered. Could I cover up the flaw with a little embroidery? Yes, that would work!

I picked a lizard embroidery design and some bright colors to match the southwest print and embroidered the design on the sleeve to cover up the flaw and it worked great! You can still see the flaw, but your eye is now attracted to the embroidery design instead of the flaw so no one ever notices it. Showing the husband my embroidery solution, he suggested embroidering another lizard on the other sleeve to balance out the design. So, I picked some more bright colors and embroidered another lizard on the other arm. With the lizard designs embroidered on each sleeve, it did not take long to complete the hems and sew on some bright southwest looking buttons to complete the shirt.

DSCN4026I was a little apprehensive about wearing this shirt at first with its bright colors and it’s multiple embroidery designs, but it did not take long to fall in love with the shirt. It is a lot of fun to wear! The color blocking, bright colors, and the embroidered designs make it highly unique. This shirt also fits well. The alterations to the pattern for the color blocking did not affect the fit.

I am very pleased with this shirt and have already worn it several times. I am now excited to make more projects with lots of color blocking and embroidery designs but minus the flawed fabric.

Until then, sew forth and lizard on!

Look WHOO’s Here For Thanksgiving!

IMG_2840
As I made my list this year of the many things that I am thankful for, I decided to include my fabric stash in the list.

YES! I am VERY thankful for my fabric stash!

Like a fine wine, it is a place for my fabric to age and rest until it is time to be sewn into something wonderful. It seems that the fabric I buy HAS to spend a certain amount of time in the stash to age and breath before I can use it.

That was not true for this fabric though…

Joann’s had a doorbuster sale on holiday fabric. At 60% off, how could I not buy some? Sitting on the doorbuster deal shelf was this cute Thanksgiving owl printed fabric. When I saw it, I knew I wanted a shirt made from it. So, I bought enough fabric to make me a typical shirt with it. Off I went straight home with it to the sewing room, bypassing the stash completely.

DSCN3819I pushed all of my other sewing projects aside and got started on my new Thanksgiving shirt straight away!

This was a very odd feeling for me…

Here I was ready to prep and cut this fabric within hours of purchasing it, and it had not yet spent its allotted time in the stash to properly breath and age. I blame the recently made Snoopy shirt for this reckless use of fabric on my part. After cutting and sewing such a precious fabric as the snoopy fabric, why not try using another recently purchased fabric?

I started the construction process by pre-washing the fabric and I am so happy that I did not skip this step.

This fabric shrank. A LOT!

DSCN3820I could still get my shirt from it but there would be little to no scraps remaining when I was done. After washing and ironing the fabric, I pulled out my collarless button front basic sloper pattern and the cutting process started.

Knowing that I had just enough fabric to make this shirt, I tried to cut carefully, but I did not cut carefully enough. I cut two right facings, and I did not have enough fabric left to cut a left facing. Since the facing on this shirt will not be seen, I thought about making the facings from a different fabric, but as I fiddled with the scraps of this fabric that was left, I determined I could cut the left facing from the scraps if I put a seam across the middle of the facing. Once again, since the facings will not be seen, I decided to try the seamed facings first. If it looked bad or was bulky or messed with the buttons or buttonholes, I could always cut out some new facings from a different fabric.

DSCN3821So with that, I began the process of sewing it into a finished garment.

The sewing of this shirt went smoothly. I have made this basic sloper many times without problems. When the shirt was completed, you would not have known that I had to piece the left facing together. The seam did not add any bulk to the front of shirt and it is in between the third and fourth button so no one will know it is there but me.

IMG_2870The shirt wore great as I gobbled down turkey, sweet potatoes and pumpkin pie in it on Thanksgiving Day.

The shirt is very comfortable and I have received a few compliments on it.

So with that I will add one more thing I am thankful for this Thanksgiving. I am thankful to have a fun Thanksgiving shirt for one of my favorite holidays. I am also thankful that I did not make this fabric spend a year or two in the stash before sewing it up into this shirt.

I have wore it all month long now and with November nearly over, I can’t wait for next year just so I can wear it again!

Until then, sew forth and gobble till ya wobble on!