Tag Archive | lining

Creative Determining – Part 2

DSCN3986DSCN3987To begin the the sewing process of the Snoopy peplum top I started with the peplum first.

Since I was not going to line the peplum, I wanted to hide all the seams as much as possible, so I sewed French seams to piece the peplum together.

 

This was not difficult, just time consuming with a lot of ironing in between seams. I did a simple 1/2 inch hem at the bottom of the peplum to complete it.

Sewing the bodice was next. I decided at the last minute to add the yellow sleeves to the top. I like the yellow sleeves but as I snipped the curve of one of the sleeves I caught the lining and so I had to do a little mending. Luckily, the mended spot is on the inside of the top and cannot be seen from the outside. It should not affect the wearing of the top.

DSCN3998DSCN3989After gathering the peplum, I sewed the peplum to the bodice, making sure to line up the seams as much as possible. I serged this seam to finish it, rather than covering the seam with the lining and doing the stitch in the ditch seam.

The serged seam looks fine and saved me the headache of doing the stitch in the ditch seam.

 

I probably could have used the practice sewing the stitch in the ditch seam on this top, but sometimes just sewing the easy and simple way is fun too. And it’s much less stressful too!

With that, the little girl’s peplum top from the leftover Snoopy fabric scraps was completed!

DSCN3995DSCN3994The top is just adorable and the multiple seams in the peplum are really not that noticeable with the gathers.

This was a fun sew.

It is always fun to make something from nothing and to let the creative side flow to make it work.

Unfortunately, now that I have used up all the Snoopy scraps, I have at least a hundred projects that have raced through my mind that I could have made using the scraps.

Having said that though, I am not disappointed at all that I used these Snoopy scraps to make this top and at least they were put to good use!

Until then, sew forth and determine on!

Creative Determining – Part 1

DSCN3986There was no way that I was going to throw away any of the precious Snoopy fabric scraps left over from my new Snoopy shirt. The scraps really were not large enough to make anything with, not even for a child, but I just could not bear to throw them away. So, what to do with these scraps beside stack them on the edge of the cutting table and stare at them?

Recently, I have seen several little girls peplum tops that are just adorable and I have wanted to make one. So, looking at the Snoopy fabric scraps, I decided to see if I could squeeze a little girl’s peplum top out of the pieces. The size of top I would make would be determined by the dimensions of the scraps.

DSCN3813I didn’t really have a pattern so I turned to the internet for ideas. The first style of peplum top I found had a circular peplum. This was out of the question. The scraps I had to work with were absolutely too small to cut a circular peplum from. The second style I found was a gathered peplum. Hmmm. I might be able to make this work with the scraps.

DSCN3985Now, how long should the peplum be versus the length of the bodice? I saw a variety of bodice and peplum lengths from long bodices with short peplums to short bodices with long peplums and many hi/low peplums in between while I was searching. Once again, I would need to let the dimensions of the scraps determine the length of the peplum and the bodice and the scraps would also determine how full the gathered peplum would be.

DSCN3999Still not having a pattern, I pulled out my favorite little girls dress pattern as a guide. Based on the size of the largest scrap, I determined that I could get a size 4 bodice front and back from the scraps as well as have a few pieces left over for the peplum. I quickly picked some yellow cotton from the stash that matched Woodstock for the lining of the bodice.

To make the peplum, I squared the remaining scraps of Snoopy fabric I had and found that I had two pieces approximately 6 inches tall by 12 inches wide and 4 pieces that were 6 inches tall by 6 inches wide. (Actually, one of the 6 by 6 inches pieces was only DSCN39965 inches wide, but I could work with that.) With a lot of seam work, I determined that I could make these scraps work out for the peplum. I would sew the two 12 wide pieces together for the front of the peplum and sew the 6 inches pieces together for the back or the peplum.

I would not be matching any of the designs in the Snoopy fabric. There was certainly not enough scraps for that, but luckily with a gathered peplum, the non-matching designs as well as the many seams that I would be sewing would just be gathered in.

Excitement for this project grew, as I saw my almost useless scraps become a little girls peplum top!

Stay tuned for the sewing of the little girl’s Snoopy peplum top.

Until then, sew forth and scrap on!

Applying The Lessons Learned

IMG_0016After being so pleased with the construction process of the dinosaur vest, and then so flustered by the construction of the ant jar vest, I wanted to make another vest. And in the process I wanted to apply the lessons that I had learned and to end the vest making process on a more positive note.

So, I grabbed some more bottom weight scraps from my pile and some monkey printed flannel and I got started! As I laid out the fabric to cut, I spied some pleather that I had waiting to make its way it to the stash. Oh yes! I would give this vest a pleather collar and welt pleather pockets to step up the style!

DSCN3956With the design completed, I started to cut out the fabric. Because I was working with scraps, I did not have a single piece big enough to cut the back of the vest on the fold, so I would need to add a back seam to this vest. A back seam would not affect the wear or the construction of the vest so I saw no problems in having a back seam. Applying the lessons learned from the previous vest constructions, I remembered to cut the extra inch for the buttons on the fronts of both the top fabric and the lining. I also remembered that I wanted to add some interfacing to the pleather the next time I used it. Soon, I had all the pieces cut out, interfaced, and I was ready to start sewing.

DSCN3957The first step in the sewing process was the embroidering of the monkey design. Remembering the lessons learned from before about placement, I thought long and hard about the placement of the embroidery design versus the size of the design and the collar before I finally hooped the fabric and stitched the design. When the design was completed, I saw that I was not going to have an issue with the collar covering the design. If fact, I had over compensated and I was wishing that the design was a little higher than it was. Even though, the monkey design is the best placed embroidery design I have done on these vests, I still have a few placement lessons left to learn.

DSCN3700The next step was to sew the pleather welted pockets. As I debated about the placement of the welts, the husband peaked over my shoulder to see what I was doing. When I showed him the pleather welts, he said no, that I should make patch pockets like on the dinosaur vest from the pleather. I explained to him that I already had the welt pockets cut out and interfacing applied to the pleather welts, but he insisted that I should cut new patch pockets from the pleather instead. Since I know that the husband has a good eye for design I followed his lead and cut out some new patch pockets from the pleather and sewed them on the front of the vest. The pockets came out great! The pleather was easy to sew and the pockets look very good on the front of the vest. Plus, the monkey embroidery design sits at the top of the pockets so it is now not too low.

DSCN3702When it came to the pleather collar and the pockets, I remembered lessons learned about using a press cloth to iron the pleather. I top stitched the edge of the collar so that it would match the stitching on the pleather patch pockets. The rest of the sewing process went smoothly, even the stitch in the ditch seam of the band.

When it came time for the buttons and buttonholes, I applied the lessons learned from the previous vest’s buttons and buttonholes. I decided not to have a button at the top of the vest, but to place the first button so the vest was open as I expected the vest to be worn. I then spaced the other buttons appropriately. The buttons looked like they were in the right place and there was no seam issues when sewing the buttonholes.

DSCN3963I am super pleased with the end results of this vest! It is just adorable!

And as much as I hate to say it, the husband was right and I just love the pleather patch pockets!

The pleather patch pockets are just perfect with the monkey embroidery design and the pleather collar.

Plus, I am super pleased with myself for remembering and applying the lessons learned from previous sewing projects.

I hope some little girl will enjoy wearing this vest as much as I have enjoyed making it. With the success of this vest, I am ready to more on from vest construction to other sewing projects, but I will happily make more vests at anytime.

Until then, sew forth and apply your lessons learned on!

Some Lessons Learned For Next Time – Part 2

Continuing on with the sewing of the denim ants in a jar vest…

DSCN3525The next step in the sewing process was to add the pockets. Since I really did not have a pattern for the side seam pockets, I decided I would design and sew them how I wanted. In designing the pockets, I wanted the fun flannel I was using to make the pockets to show, so I decided to cut a rectangle from the sides of the jacket fronts. But, how big should I cut the rectangle? After some thought, I cut the rectangle what I thought the size should be, 5 inches tall by 1 inch deep, and then cut the pockets to match. With this size of square, I would place the pocket 1.5 inches from the bottom of the fronts.

DSCN3524In the sewing process, I noticed right away that I had a good size opening for the pockets but not much depth to the pockets. I should have cut the opening square shorter and used that extra length for the pocket depth. It was too late now though as the fabric was already cut. So, the finished pockets are very cute and the flannel is showing, and the pockets will certainly keep the wearer’s hands warm but the pockets won’t be too useful for hold many items due to their short depth. Another lesson learned for the next time!

DSCN3530The next step was to add the bottom band which was a little difficult due to the stiffness and weight of the denim. I had to use a little liquid stitch to help hold the denim in place to start and stop the stitch in the ditch seam. There was a lot of bulk from the denim front, the seam allowance from attaching the band, and the folded over finish of the band, i.e. 5 layers, in this seam. I trimmed the seam allowance but it was still bulky and difficult for my sewing machine to get started on this final band seam, but I made it through it ok.

DSCN3531The final step was to add the buttons. I measured evenly to place the buttons, but when it came to sewing them on, I had to move the top button down slightly due to the bulky denim seam at the top of the vest. This left the buttons mis-spaced slightly. The top button is not quite high enough to keep the vest closed around the neck if it is worn closed. If the top button is left undone, the vest opens a little too much before the next button. This could have been avoided by sewing horizontal buttonholes and avoiding the DSCN3928 (1)bulky denim seam at the top, but because of the pieced strip on the front of the vest to add the extra inch, I had to make the buttonholes vertical. If I had given the placement of the buttons versus the bulky denim seams a little more thought before I started to sew, I could have placed the buttons better. Another lesson learned for next time!

Now that the vest is complete, I am pleased with the end results. I also think the vest will wear just fine, and I hope some kid will enjoy wearing it too. Many lessons were learned from the making of this vest and I hope to remember all these lessons and apply the lessons to my future sewing projects.

Until then, sew forth and button on!

Some Lessons Learned For Next Time – Part 1

DSCN3928 (2)My latest sewing project was destined to be yet another learning experience for me.

After the successful sewing of the dinosaur vest, I wanted to make another vest. When I made the dinosaur vest, I had envisioned so many different options and fabrics for these vests, so this made it easy to decide that my next sewing project would be to make some of these vest options a reality!

The designing of this vest was not difficult at all. When I was picking out the fabric for the dinosaur vest, I had also pulled out a denim scrap that was just big enough to make a vest and a greenish blue flannel with yellow bug outlines from the stash. I could see a vest from these two pieces of fabric and I knew that I would sew one of my favorite embroidery designs, some ants escaping from a glass jar, on the front. Because of the large size of the embroidery design, I would give this vest side seam pockets rather than patch pockets.

With the design of the vest all outlined, it was time to cut it out and get sewing!
DSCN3931 (1)When I laid out the pattern pieces of Simplicity 8902, on the denim fabric, I remembered that I needed to add an inch to each front for the button overlap. I carefully laid the pattern pieces out correctly to cut the extra inch, but then I promptly cut along the edge of the pattern piece as shown on the pattern and I did not add the extra inch. How dumb was that? Well it was done now and I couldnt undo it so I decided it was a lesson to be learned for the next time I make this pattern.

The denim scrap that I had was not big enough to cut two new fronts, so instead I cut two 1.5 inch strips of the denim to add to the fronts of the vest. The strip would look like an intended button placket rather than a fix, so all was good despite the cutting error that I made. After cutting out all the pieces and remembering to add the extra inch to the front of the lining, it was time to being sewing.

DSCN3930 (1)The sewing process started with embroidering the design to the front of the jacket. I remembered that I wanted to do the embroidering first before adding the pockets to keep the pockets out of the way of the embroidery. I also remembered that I wanted to move the embroidery design down so that there would not be an issue with the collar covering some of the design.

What I had forgotten was that the ants embroidery design is two inches taller than the dinosaur design and I did not remember to take that into account when positioning the design. So, even though I moved the design down on the vest, the top of the design was still higher than I wanted it due to the extra height of the design. After stitching the design to the front of the vest, I realized that the top of the ant design was still going to be under the collar, and not just at the edge of the collar like the dinosaur design but that the ant at the top was going to be under the collar. That will be another lesson learned for next time I use this design!

DSCN3932 (1)Flustered even more, I now had to come up with a solution to fix the collar/embroidery design problem. I thought about making this vest collarless or adding a standing ribbing collar that would not fold over, but I did not like the look of these options.

I decided to see if I could just shorten the collar enough so that it would not cover the ants but it would still fold over and look ok. To do that I cut over an inch ff the bottom of the collar. The collar looks a little small now that it is done, but it works just fine. The collar lays right at the edge of the top ant’s antenna, and with a little encouragement, the stiff denim will fold over just enough to cover the collar seam. Still not being totally pleased with the collar, I continued on with the sewing process to the next steps.

But that’s a story for next time.

Until then, sew forth and ant on!

Oh! That’s Gonna Leave a Welt… – Part 2

DSCN0977Continuing on from my first part of the welt pocketed jacket project, the rest of the jacket sewing went smoothly.

I used pleather for the collar as well as the pockets and it all sewed up great! Because the zipper was not inserted into the collar, there was no hand stitching and I was able to finish off the collar with some twill tape. I also remembered to press the pleather with a press cloth on both the pockets and the collar so that the iron did not damage the pleather. Before long the sewing was done and the jacket was complete.

With the jacket completed, I studied it closely and something was not right.

DSCN0981I stared at and studied the jacket until I finally figured out what that something was. The neckline on this jacket is HUGE! It is way too big around. I returned to the pattern, but as far as I could tell, I had traced and cut the pattern pieces correctly. Had I sewed something wrong or was it the pattern? I had a few options to try and fix it. I could try to fix the neckline, but for a trial jacket, I was not willing to spend the time and energy on a fix, especially to find out that the fix didn’t work or made things worse. Disappointed, I thought about not embroidering on the jacket, but then decided that some kid somewhere would be willing to wear this jacket, and he or she would need something fun embroidered on it to distract from the huge neck line.

DSCN0922Picking an embroidery design for this jacket was not an easy task. Since I did not know who the final owner of this jacket would be, I tried to make it as unisex as possible, but each embroidery design I picked swayed the jacket to the feminine or masculine side. I looked and debated over many designs until I finally realized that I was wasting all my sewing and embroidery time picking out the design. I finally went back to one of my first choices and embroidered The Lady and The Tramp design on the jacket. The jacket is definitely for a girl now but I love the design on it.

DSCN0982I am still not happy with the collar on this jacket, but I am very pleased with the welt pockets, the pleather accents and the embroidery design.

Ultimately, I am happy with the end results of this jacket and hope that there is a young girl out there willing to wear this jacket even with the oversized collar. I am super excited about learning to make welt pockets and I cannot wait to start another project with welt pockets!

Until then, sew forth and welt on!

Oh! That’s Gonna Leave a Welt… – Part 1

DSCN0977I decided that is was time to try making welt pockets.

Welt pockets always look so nice and professional, plus I had something special I wanted to try for the welts. One day while shopping at Walmart, I saw a couple of bolts of patterned pleather and I knew right away that it would be perfect to make the welts for the welt pockets from. I quickly purchased some, and headed for my sewing room.

First, I needed a pattern. After looking through my pattern stash, I turned to my Kwik Sew books on the shelf.

Yes, there were jacket patterns with welt pockets and instructions in these books. I was super excited and ready to get started!

Next, I had to choose a fabric for the jacket. I had a bright yellow sweatshirt fleece hiding in the stash and debated if pleather and sweatshirt fleece would look good together. I finally decided that they would, especially for a first try of welt pockets. It was easy to pick out some left over scraps from one of my shirts for the body of the pockets.

DSCN0827DSCN0830And I decided to make a size 8 jacket because of the length of the zipper I had. I would need to lengthen the jacket a little to accommodate the zipper, but I didn’t think that would affect the wearing of the jacket.

The first step in making this jacket was to see if pleather would survive the washer and dryer.

It did! And beautifully I might add!

The next step was to see if my sewing machine would sew the pleather or if I was going to require a special foot, needle and thread for sewing the pleather. I did not. The pleather sewed beautifully with just my normal pressure foot, regulars thread and a new Schmit universal needle.

DSCN0833DSCN0836Wow! I had read horror stories on the internet about sewing with leather but I guess pleather is different, or maybe just these particular pieces. Regardless, I was excited!

With the pattern traced and the fabric cut, it was time to get sewing.

To sew the welt pockets, I started with some scraps to get an idea of what I was doing, then I moved on to the jacket.

DSCN0838DSCN0842I started by applying a pieces of interfacing with the sewing lines to the front of the jacket. Next, I taped the pleather in place and then O sewed around the lines.. I taped it because I did not want to scar the pleather with pins. Cutting was next and then pulling the pleather to the wrong side to form the hole for the pocket. Then I folded up the welt and sewed it in place, and then I attached the body of the pocket to the pleather and finally I sewed around the body of the pockets.

DSCN0848DSCN0844Soon enough, I had completed the two welt pockets. They are not perfect but they were fun to make and I really like the results especially with the pleather.

I debated about interfacing the pleather of the welt but I thought that the pleather was stiff enough to not need interfacing. As I inserted my hand into the pocket, past the welt, I wished that I had interfaced the welt and made it stiffer to withstand use over time.

I had pictured the welts as being bigger than they finished up being. Knowing now how to make welt pockets, I feel that I can make the welts in different sizes and styles the next time I make something with welt pockets.

Coming up next, the completing of the jacket.

Until then, sew forth and welt on!

It A Trap (ezoid) Skirt!

DSCN2926When I found this trapezoid scalloped edged girl’s skirt pattern on the internet, I knew exactly what I wanted to do with the scraps that I had leftover from my minion shirt. The combination of the minion fabric, the banana fabric and the blue fabic had made for a fun shirt and it would definitely make a fun skirt too.

I was excited to get sewing but I knew that I had to start with a little math before I could take the first stitch.

Yes that’s right kids! Your teachers WERE RIGHT about the using math outside of school thing! Imagine that!

Since I was sewing empirically here, and not making this skirt for anyone in particular, so no particular size, I had to calculate how big I could make the trapezoids versus the amount of scraps that I had.

DSCN2554Luckily I’m not afraid of a little math, so after a few calculations, I found that I had enough scraps for a girl’s size 6 to 8 skirt, making the trapezoids 3 inches at the top and 5 inches at the bottom and 15 inches long. And as per my calculations, I would be cutting out 18 trapezoids in total, 6 from each of the three different fabrics and that would use up all the scraps I had.

I first cut myself out a trapezoid pattern piece and then I used it to start cutting. I tried to cut as accurately as possible so that all the pieces fit together nicely and would be even.

DSCN2717Cutting out the pieces took some time, but sewing the trapezoids together took even more time, plus each seam had to be pressed after I sewed them. I sewed each trapezoid from the bottom to the top to keep them as even as possible.

After the trapezoids were all sewn together, I used the skirt as my pattern to cut out the lining for the skirt. The pattern only called for only a small strip of lining to be used at the bottom of the skirt to make the scalloped hem, but I decided to fully line to skirt. This would take care of finishing all the trapezoid seams, and it would keep the girl’s panties from showing through the thinner minion and banana fabric and eliminate the hand stitching the pattern called for at the hem from only using a strip of lining.

DSCN2718Cutting the lining caused me a few moments of anxiety because of the amount of fabric needed to cut the lining. The skirt was made of scraps so really no large or useful sizes of fabric were used, but when the trapezoids were sewn together, they formed a circle skirt, and cutting a full lining on grain for a circle skirt did require a real size piece of fabric.

In fact, cutting this lining pretty much used up all the yellow lining fabric I had purchased on sale a while back. I was sad that this lining fabric was now all gone. It had been a great piece to turn to when I needed a lining for the little girls dress I had made. But, the husband comforted me by reminding me that there was now one less piece of fabric in the stash and that now I could go and buy more lining fabric. And who doesn’t love to go fabric shopping? Not me, that’s for sure!

DSCN2720With the lining all cut out and the its side seams sewn, placing right sides together and matching the hem, I sewed around the hem. At this time I cut out a cardboard circle to use as the pattern for the scalloped hem. I traced the circle onto the skirt, matching the seams of the trapezoids and the stitch line at the hem. After tracing a scallop on each trapezoid, I carefully sewed around each scallop edge. Trimming and snipping around each scallop was the next step followed by turning the skirt right side out. It was now time for a lot of pressing to the skirt hem.

DSCN2727Once the scalloped hem was done and pressed, it was time for the waist band. I had planned to use 3/4 inch elastic in the waist, so with a few more calculations, I cut the waist band from the blue fabric 2.5 inches wide and long enough to go around the top of the skirt. With right sides together, I sewed the waist band to the top of the skirt, serged the edges and pressed it towards the top of the waist band. I then serged the top edge of the waist band and pressed it over about 1/4 inch. I then folded and pressed the waistband over and stitched in the ditch to finish it off. I left a small unsewn portion to insert the elastic. I also added a small tag to the waist band to denote the back of the skirt from the front, although this skirt really does not have a front or back.

DSCN2723After the waist band was sewn up, it looked short, too short to fit 3/4 inches elastic into it. I am not sure where my calculations went wrong but I should have cut the waist band wider. I debated about unpicking the waist band and cutting a new wider waistband, but the thought of unpicking all the serging was unbearable, so I decided to use 1/2 inch elastic instead of the 3/4 inch that I had planned on. The 1/2 inch elastic fit into the waist band just fine and I think because this skirt is for a younger girl, the 1/2 inch elastic will wear fine too.

DSCN2725To determine how much elastic to use in the waistband, I measured the length of my finished skirt of approximately 15.5 inches. Looking at a chart I had downloaded off the internet, I cut my elastic 25 inches in length. 24 inches for the waistband and 1 inch for sewing it together. This length of elastic plus the length of the skirt meant I had made approximately a small size 8 skirt.

This worked for me. I do not think an eight year old girl is too old for a minion skirt. If I’m not too old for a minion shirt then an 8 year old girl is certainly not too old for a minion skirt. Perhaps I am just still young at heart!

DSCN2734I decided to do a decorative top stitch around the scalloped edge of the hem of this skirt. I think the scallops were sewn fine before I did this, but because this is a play skirt, and I am expecting it to be worn while running and jumping, a little extra strength at the hem certainly won’t hurt.

I think that this skirt turned out to be just adorable, and I am excited for a young girl to wear it and enjoy the minion and banana fabric as much as I have enjoyed making it!

This skirt has also given me one more option to use up my scraps with and I will keep it in mind that next time I am debating about what to do with a pile of scraps.

Until next time, sew forth and trapezoid on!

Invested

DSCN1372DSCN2485 (1)Do you ever have a pattern speak to you when you see it?

Me! Me! Me! Sew me next! Sew me next! Pick me! Pick me!

Well, this pattern did not just speak to me, it screamed at me!

The minute I saw this free vest pattern on the internet, I abandoned all of my other sewing plans.

Since I could not ignore its request to be sewn next, a boy’s vest became my next sewing project.

DSCN2491DSCN2492What caught my attention about this vest pattern was the endless creative possibilities that it presented.

From the fabric I would use to make this vest, to the type of pockets I would sew, to the embroidery and details I would stitch, there were dozens of designs decisions to be made.

First off, I picked the fabric. I choose some sport weight scraps for the outer layer of this vest and some flannel for the lining.

I did question using flannel for the lining though.

The smooth slippery fabric of a lining helps with taking an item on and off. Flannel is not smooth or slippery and would actually make it more difficult to pull an item on and off.

But, since this is a vest, i.e. without sleeves, I figured the flannel would be fine to use. Plus, it would add a layer of warmth to the vest, and as an added bonus, I would be using some of the flannel hiding in the stash and most importantly, I could incorporate the print of the flannel with the embroidery design that I would be stitching on it. So, it was not difficult to pick the dinosaur flannel fabric for the lining and a dinosaur embroidery design.

DSCN1364DSCN1365When it came to deciding on pockets, I liked the patch pockets that were used on the pattern so I decided to make them.

The pockets are not just typical patch pockets so there would probably be something new for me to learn from sewing them.

I started the process by downloading the pattern, printing it out, taping it together, cutting it out, and then throwing it away. Yes, you read that right. I threw it away.

DSCN1373DSCN2488As I laid the pattern pieces on the fabric, I did not like the way they looked at all. I couldn’t get the shoulder seams to match and the armscye looked misshaped.

I could see many problems occurring during the sewing process using that pattern and I did not want to waste my time or fabric on a doomed project.

I was disappointed to say the least.

I was so excited to make this vest and I had already put so much planning into it’s design that I did not want to just abandon the project.

So I turned to my pattern stash and what do you know! Lying right on top was a jacket pattern, Simplicity 8902.

Could I possibly use this jacket pattern to make a vest by just leave the sleeves off?

DSCN2487DSCN2486 (1)I did not know the answer to this question but I was certainly willing to find out.

I began to cut out the pieces for this vest from it. Since I was going to use buttons instead of a zipper, I added an extra 1 inch to the front pieces.

I also ironed on a strip of interfacing to this extra inch to strengthen it for the buttons.

My first step in the sewing process was to sew the pockets on the front of the vest.

Embroidering the dinosaur design was next. Then I sewed the shoulder seams and collar. It was then that I realized I should have reversed these steps. The collar is slightly covering the top the embroidery design. If the design had been any bigger, it would have been hidden under the collar.

The next time, I will sew the shoulder seams and attach the collar first and then embroider the design placing it so the collar is not in its way. Then I will attach the pockets last.

DSCN1368DSCN1369This way I will have no problem hooping the fabric for the embroidering without the pockets on the front, and after embroidering, I can place the pockets over the fabric that was hooped.

The original vest pattern had a bottom band. I liked the look of the band so I decided to keep it on this vest, so I cut the vest and lining 2 inches shorter than the pattern called for to accommodate the bottom band. Because of the bottom band, it was easy to sew the lining to the vest.

With right sides together, I sewed around the vest and lining before sewing the side seams then turned it inside out and sewed the side seams. After a lot of pressing, I sewed the band to the front side of the vest and lining and then folded it to the back and stitched in the ditch to finish up the band.

DSCN1374DSCN2490 (1)The last step was to sew the buttonholes and buttons.

I sewed vertical buttonholes so that my buttonholer would not have to move over the pockets. I don’t believe that vertical buttonholes will make a difference in how the vest wears.

In the end the vest turned out absolutely adorable!

I just love it, and it was so much fun to design and make that I can’t wait to make another one.

I have not given this vest to anyone yet so I do not have a “wear test” to tell me whether a jacket without sleeves makes for an acceptable vest, but it looks good to me.

I could always make the armscye a little bigger on the next vest to ease my mind and the fit.

So until the next time, sew forth and vest on!

The Making of the Doctor Who Reversible Sling Bag – Part 2 – The Construction

dscn1157dscn1149The construction of the Doctor Who reversible sling bag began with cutting out the pattern pieces from the fabric. I remembered to cut the length 1 inches longer and the strap 3 inches longer as I had previously decided to do as I cut the black bottom weight pieces and the Doctor Who Dalek fabric.

dscn1150dscn1139But as I cut out the striped fabric, the stripes started to play with my brain and I cut out one piece correctly, and three pieces incorrectly with 3 inches extra on the bottom and only 1 inch extra on the straps. When I realized my error, I thought about cutting the 3 pieces out again correctly but I hated to waste the fabric. I had purchased this fabric for another project and had cut the pieces for this bag conservatively as to leave as much fabric as possible for that other project. That lead me to decide to make my already cut out pieces work out some how instead of cutting out corrected pieces.

dscn1128dscn1126The sewing process started with the insert seams and the bottom seams. I matched the insert seams at the top of the bag because of the extra inches at the bottom of the stripes, then cut off the extra before sewing the bottom of the bag. Next was the seam that I called the pinch. This is the seam that squares the bag to give the bag a bottom. It is sewn by first pinching the corners of the bottom seam of the bag and then stitching across the pinch. The pinch was easy with the bottom weight fabric of the Dalek fabric side of the bag. I measured and sewed carefully and the pinch turn out great.

dscn1129dscn1130The striped fabric was not as easy. Because it is a thin lining fabric, it wanted to slip and slide as I measured and sewed the pinch but with patience, I finally got acceptable results. These pinch seams weren’t that hard so I stopped being as careful and learned very quickly that that was a bad move. My next pinches went terribly wrong when I did not carefully measure and sew them. I ended up unpicking and re-measuring and re-sewing all 4 of the pinches on the second bag to get nicer pinches. Lesson learned, take the time needed to do the job right the first time.

dscn1132dscn1141The next step was to sew the two parts of the Dalek/black bag and stripe/black together. With rights sides together, I sewed around the curves of the top of the bags. Each bag was then turned right side out through the strap. This was a bit of a challenge but with time and patience the bags were turned right side out.

Now it was time to fix my cutting error. The striped fabric was 4 inches too short on the strap, 2 inches on each side. I had several options for fixing this problem, like just sewing more fabric to the stripe fabric dscn1146but I wanted to make sure it was very secure at the shoulder. I finally opted to dscn1144make a patch from the black fabric to cover the missing stripe fabric. I cut a piece of the black fabric big enough to cover the missing piece with seam allowances. I folded over the edges and ironed them in place then applied some seam to seam to the edges. I then ironed the patch in place. I sewed the patches in place as I top stitched the edges of the bag. The patch worked great to solve my cutting error, and because the patches are at the shoulder, it looks like I meant to add the patch to the strap as reinforcement.

dscn1134dscn1136The final bags turned out great. I was concerned at first about the bag not having a closure as it gapped when I placed it my shoulder but when I added a book to the bag, the weight of the book closed the bag. I took the bags to my coworker the next day. I showed her that they were reversible and told her if her daughters wanted a closure on the bags to bring them back to me. Her daughters called me the next day to tell me how much they liked the bags and that they had used the bags for their books at school that day instead of their regular back packs. I was excited to hear that the bags were a success and that they liked them and that they used them. It did my sewing heart good.

dscn1135dscn1159These bags were great fun to make and as always I learned some new sewing lessons from making them.

After this project, I see more sling bags in my future. Maybe next time with pockets and closures with Snoopy or Mickey Mouse fabric or maybe even more Doctor Who fabric.

I also have some great Marvel Comics fabric that I was wondering what to do with and San Diego Comic Con is coming up shortly!

dscn1155Oh, this is going to be fun!dscn1154

Until next time, sew forth and Trust the Doctor on!