Tag Archive | seam

Creative Determining – Part 2

DSCN3986DSCN3987To begin the the sewing process of the Snoopy peplum top I started with the peplum first.

Since I was not going to line the peplum, I wanted to hide all the seams as much as possible, so I sewed French seams to piece the peplum together.

 

This was not difficult, just time consuming with a lot of ironing in between seams. I did a simple 1/2 inch hem at the bottom of the peplum to complete it.

Sewing the bodice was next. I decided at the last minute to add the yellow sleeves to the top. I like the yellow sleeves but as I snipped the curve of one of the sleeves I caught the lining and so I had to do a little mending. Luckily, the mended spot is on the inside of the top and cannot be seen from the outside. It should not affect the wearing of the top.

DSCN3998DSCN3989After gathering the peplum, I sewed the peplum to the bodice, making sure to line up the seams as much as possible. I serged this seam to finish it, rather than covering the seam with the lining and doing the stitch in the ditch seam.

The serged seam looks fine and saved me the headache of doing the stitch in the ditch seam.

 

I probably could have used the practice sewing the stitch in the ditch seam on this top, but sometimes just sewing the easy and simple way is fun too. And it’s much less stressful too!

With that, the little girl’s peplum top from the leftover Snoopy fabric scraps was completed!

DSCN3995DSCN3994The top is just adorable and the multiple seams in the peplum are really not that noticeable with the gathers.

This was a fun sew.

It is always fun to make something from nothing and to let the creative side flow to make it work.

Unfortunately, now that I have used up all the Snoopy scraps, I have at least a hundred projects that have raced through my mind that I could have made using the scraps.

Having said that though, I am not disappointed at all that I used these Snoopy scraps to make this top and at least they were put to good use!

Until then, sew forth and determine on!

Creative Determining – Part 1

DSCN3986There was no way that I was going to throw away any of the precious Snoopy fabric scraps left over from my new Snoopy shirt. The scraps really were not large enough to make anything with, not even for a child, but I just could not bear to throw them away. So, what to do with these scraps beside stack them on the edge of the cutting table and stare at them?

Recently, I have seen several little girls peplum tops that are just adorable and I have wanted to make one. So, looking at the Snoopy fabric scraps, I decided to see if I could squeeze a little girl’s peplum top out of the pieces. The size of top I would make would be determined by the dimensions of the scraps.

DSCN3813I didn’t really have a pattern so I turned to the internet for ideas. The first style of peplum top I found had a circular peplum. This was out of the question. The scraps I had to work with were absolutely too small to cut a circular peplum from. The second style I found was a gathered peplum. Hmmm. I might be able to make this work with the scraps.

DSCN3985Now, how long should the peplum be versus the length of the bodice? I saw a variety of bodice and peplum lengths from long bodices with short peplums to short bodices with long peplums and many hi/low peplums in between while I was searching. Once again, I would need to let the dimensions of the scraps determine the length of the peplum and the bodice and the scraps would also determine how full the gathered peplum would be.

DSCN3999Still not having a pattern, I pulled out my favorite little girls dress pattern as a guide. Based on the size of the largest scrap, I determined that I could get a size 4 bodice front and back from the scraps as well as have a few pieces left over for the peplum. I quickly picked some yellow cotton from the stash that matched Woodstock for the lining of the bodice.

To make the peplum, I squared the remaining scraps of Snoopy fabric I had and found that I had two pieces approximately 6 inches tall by 12 inches wide and 4 pieces that were 6 inches tall by 6 inches wide. (Actually, one of the 6 by 6 inches pieces was only DSCN39965 inches wide, but I could work with that.) With a lot of seam work, I determined that I could make these scraps work out for the peplum. I would sew the two 12 wide pieces together for the front of the peplum and sew the 6 inches pieces together for the back or the peplum.

I would not be matching any of the designs in the Snoopy fabric. There was certainly not enough scraps for that, but luckily with a gathered peplum, the non-matching designs as well as the many seams that I would be sewing would just be gathered in.

Excitement for this project grew, as I saw my almost useless scraps become a little girls peplum top!

Stay tuned for the sewing of the little girl’s Snoopy peplum top.

Until then, sew forth and scrap on!

Applying The Lessons Learned

IMG_0016After being so pleased with the construction process of the dinosaur vest, and then so flustered by the construction of the ant jar vest, I wanted to make another vest. And in the process I wanted to apply the lessons that I had learned and to end the vest making process on a more positive note.

So, I grabbed some more bottom weight scraps from my pile and some monkey printed flannel and I got started! As I laid out the fabric to cut, I spied some pleather that I had waiting to make its way it to the stash. Oh yes! I would give this vest a pleather collar and welt pleather pockets to step up the style!

DSCN3956With the design completed, I started to cut out the fabric. Because I was working with scraps, I did not have a single piece big enough to cut the back of the vest on the fold, so I would need to add a back seam to this vest. A back seam would not affect the wear or the construction of the vest so I saw no problems in having a back seam. Applying the lessons learned from the previous vest constructions, I remembered to cut the extra inch for the buttons on the fronts of both the top fabric and the lining. I also remembered that I wanted to add some interfacing to the pleather the next time I used it. Soon, I had all the pieces cut out, interfaced, and I was ready to start sewing.

DSCN3957The first step in the sewing process was the embroidering of the monkey design. Remembering the lessons learned from before about placement, I thought long and hard about the placement of the embroidery design versus the size of the design and the collar before I finally hooped the fabric and stitched the design. When the design was completed, I saw that I was not going to have an issue with the collar covering the design. If fact, I had over compensated and I was wishing that the design was a little higher than it was. Even though, the monkey design is the best placed embroidery design I have done on these vests, I still have a few placement lessons left to learn.

DSCN3700The next step was to sew the pleather welted pockets. As I debated about the placement of the welts, the husband peaked over my shoulder to see what I was doing. When I showed him the pleather welts, he said no, that I should make patch pockets like on the dinosaur vest from the pleather. I explained to him that I already had the welt pockets cut out and interfacing applied to the pleather welts, but he insisted that I should cut new patch pockets from the pleather instead. Since I know that the husband has a good eye for design I followed his lead and cut out some new patch pockets from the pleather and sewed them on the front of the vest. The pockets came out great! The pleather was easy to sew and the pockets look very good on the front of the vest. Plus, the monkey embroidery design sits at the top of the pockets so it is now not too low.

DSCN3702When it came to the pleather collar and the pockets, I remembered lessons learned about using a press cloth to iron the pleather. I top stitched the edge of the collar so that it would match the stitching on the pleather patch pockets. The rest of the sewing process went smoothly, even the stitch in the ditch seam of the band.

When it came time for the buttons and buttonholes, I applied the lessons learned from the previous vest’s buttons and buttonholes. I decided not to have a button at the top of the vest, but to place the first button so the vest was open as I expected the vest to be worn. I then spaced the other buttons appropriately. The buttons looked like they were in the right place and there was no seam issues when sewing the buttonholes.

DSCN3963I am super pleased with the end results of this vest! It is just adorable!

And as much as I hate to say it, the husband was right and I just love the pleather patch pockets!

The pleather patch pockets are just perfect with the monkey embroidery design and the pleather collar.

Plus, I am super pleased with myself for remembering and applying the lessons learned from previous sewing projects.

I hope some little girl will enjoy wearing this vest as much as I have enjoyed making it. With the success of this vest, I am ready to more on from vest construction to other sewing projects, but I will happily make more vests at anytime.

Until then, sew forth and apply your lessons learned on!

Yay Sports! Go Team!

DSCN3421 (1)IMG (1)I am certainly not a big sports fan, and I am especially not a big football fan, but I am a BIG fan of fabric. So, you know, when I saw this football fleece on clearance at Joann’s and I also had a coupon for even more off the already low reduced price, you just knew I was going to buy some of it. And even though I may not be a big football fan, I am sure there is some one out there that is, and would want me to make something for them from this fleece.

In trying to fall in love with fleece again, I did some reading on the internet and I found some suggestions for sewing with fleece. I wanted to try out a couple of the suggestions, so I pulled out this football fleece and a simple pattern, Kwik Sew 3235, for a pullover fleece jacket. In making a pullover jacket, I won’t have to worry about buttons or a zipper, and I could focus on the seams and the suggestions I had read about.

DSCN2561DSCN2797I could not decide which size between a medium or large that I wanted to make, but as I mentioned in a previous post, the fabric decided for me. I would be making a medium pullover jacket. Also as previously mentioned, this pattern was not very easy to cut out due to the fabric. I had to really work to keep the footballs and helmets straight. When I cut out the pocket, I purposely did not match the design because I wanted the pocket to stand out from the rest of the jacket’s design.

With my pattern pieces cut out, I started the sewing process. The first suggestion I followed was to put a new needle in the machine. The suggestion said to make sure it was a ballpoint needle. I only use Schmetz universal needles so that is what I sewed it with and it did great. The next suggestion was to lengthen my stitch length because of the bulk, which I did. When it can time to iron it, I followed another suggestion of using a press cloth so I could iron the fleece a little more aggressively without hurting the fleece.

DSCN3426 (1)DSCN3429 (1)One article I read suggested three different types of seams that worked well for sewing fleece, a fake flat fell seam (sometimes called a faux flat felled seam), a lapped seam or a double topstitched seam. I was not impressed with the lapped seams but wanted to try the other two seams. As I started to sew, I found that I wanted to just sew double top stitch seams so that the seams matched. The double top stitch seam is sewn by first sewing your seam as you normally would, then sewing the seam allowances down close to the edge of the seam allowance, then trimming close to the seam allowance stitching. Since fleece does not fray, cutting close to the stitches finishes off the seam. On the top side, there is a cool double row of stitching encasing the seam. This is a fun look that looks like it took a lot of effort to sew but was really easy and it looks great! Especially if you sew straight, which I seem to have a hard time doing most of the time. 🙂

DSCN3424 (1)DSCN3423 (1)I was able to do the double top stitch seams on the shoulder seams, the sleeve seams and even the hood’s seams, but when it came time to double topstitch the underarm/side seams, I realized that would be impossible. Because the arm is a tube, there was no way I was going to fit the fabric under the presser foot and sew it. I tried to figure out a way to do the topstitching but could not. I turned to the internet for help, but pretty much everyone said the same thing that it could not be done with a normal home sewing machine.

There were a few suggestions on the internet for how to finish the seam but I was not thrilled with the answers. Pondering the possible ways to finish this seam, I stared at my serger and I shook my head. I have the tools, i.e. a serger, why not use it. So I serged the underarm/side seams to finish them. Because this is not a super heavy fleece, no issues occurred while serging it. I also used the serger to finish the edges on the facing. I could have just left the edge unfinished on the facings but that would have really bugged me.

DSCN3422 (1)For the hems, I folded and sewed the hems as usual but with out finishing the edge with the serger or folding the edges over. After completing the hems, I trimmed the edges close to the stitches as I did for the seam allowances so that all the inside seams matched. I did the same with the pockets opening edge.

Looking at the completed jacket, I liked what I saw from the outside. The top stitching looked great! From the inside though, the serged seams looked so much cleaner and finished than just the trimmed seams. But, I was not disappointed that I had done the double topstitched seams for the others. It was fun to try something different, plus I will have a new technique for sewing a heavier fleece that would not serge well in a later project.

This jacket was fun to make and turned out great!

So, am I in love with fleece again? The answer is maybe.

The cutting out of this pullover jacket was a real task, but the sewing was fun especially with applying the suggestions I had read about. I do see more fleece projects in my future so stay tuned.

Until then, fleece forth, and sports on!

Being Biased – Part 3 – Button Fitting

DSCN1300I believe I have fallen in love with bias tape.

Even though, I had a number of trial and tribulations in the making of and the sewing on of the bias tape with these tops, I can see were bias tape can be a fun accent to many sewing projects and I can’t wait to start another bias tape project.

But before I do that I needed to finish these cross back summer tops before the summer has ended so that the girls can actually get some use out of them.

All I needed to do to finish them was to add buttons and buttonholes to the back of the tops and they would be done and ready to wear.

Sounds easy enough, doesn’t it? Well, I wish would have been as easy as it sounded.

DSCN1303I knew when I cut this pattern out that this pattern does not have a true side seam. I did not think it was going to be a big deal, but it was!

The backs are cut so that the shoulder and side seams are towards the front of the top. There is no seam directly under the armscye or on the shoulder. It is just to the side of the armscye and front of the shoulder.

This pattern also has no indication of where the buttonholes should be placed. So, when it came time for me to determine where to sew the buttonholes and buttons, I had some guessing to do. DSCN1304

I started the guessing by trying to determine where the true side seam would have been on these tops. Should the back come towards the front of the top a little, like 1/2 inch, or a lot, like 2 inches.

Next, I had to determine if the cross over should match at the top and leave a big “V” at the bottom of the back or should the “V” of the cross over be smaller by lowering the top. I spent hours measuring, folding, pinning, and deciding where to put the buttons and buttonholes.

I would think that I had it all ready to sew, then I decided that it wasn’t right and I would start again. After awhile even the husband grew tired of me showing him each variation that I tried. He tried to help, but I just could not make up my mind if I had it right or not. DSCN1302

Finally, I reached a point were I truly believed that I had it measured, folded and pinned where I wanted the buttons to be so I went to the sewing machine. I carefully sewed the buttonholes and buttons in place on both tops.

When I was done, I was quite pleased with myself until I held the tops up and the back curve of the cross over flopped down over one of the special buttons I had paid a lot of money for. Crap! The buttons needed to be higher on the top.

Now, how was I going to fix this? Version 2

My first thought to solve this problem was to sew a hook and eye to the curve which would attach the curve to the back of the top. This would keep the curve from flopping over but that did not work. When the curve tried to flop over, you could see the hook and eye and it looked worse than the flopping curve of the fabric.

My next thought was to use some velcro. As I went to sew the velcro on, the husband asked what I was doing. I showed him the flopping curve and how I was trying to fix it. He said to stop. He said that since girls were sisters they could keep an eye on each other’s backs when they were wearing the tops and if the curve flopped, they could fold a crease in the bias tape so that the curve would not flop as much. This seemed like a reasonable solution to the flopping curve, so I left it at that.

20150530_124144The REAL answer to this whole problem was to have the girls try the tops on before I placed the buttons.

I could have quickly determined where the “side” and “shoulder” seams should be, how big the “V” in the back should be and where the buttons needed to be. But, I had wanted the tops to be a surprise for them so I didn’t. Even though they had picked out the fabric, they did not know what I was making from it. Plus, with them not knowing what or when I was making something, there was less pressure to get the tops completed.

With that all in mind, I determined that the surprise and less pressure to get the items completed were not worth the button/buttonhole headache, and with this lesson learned, the next time I make something for the girls, there will be fittings during the process. Version 2

Upon receiving the tops, their mom says the girls like them and will wear them. I explained to their mom the button/floppy curve issue and she said it would not be a problem.

I don’t believe that the girls were nearly as excited about these tops as they were their fun vests or their Dr Who bags, but that is ok because I learned a lot from these tops both in the sewing process itself and in the process of sewing for others. 20150530_124000

And the next time I sew for the girls, I am getting them involved in the process.

No more surprises!

I want them to pick their own fabrics, colors and styles. I want to measure them so that I have the best fit, instead of using a year old measurement that their mom took (no offense to their mom), and I want fittings and alterations done during the sewing process.

I think I will learn even more sewing for them this way and they will have exactly what they want as well. Plus NO more guessing!

Until then, sew forth and bias tape on!

Being Biased – Part 2 – The Sewing of the Bias Tape

DSCN1308I gave the process of sewing of the crossed back summer tops a lot of thought before I made the first seam.

I had read the pattern instructions, but I wanted to sew the top together with fitting in mind. I wanted to sew the seams so that the minimal amount of unpicking would be necessary if I needed to alter the size of the tops for the girls later. So, my plan was to start with sewing on the bias tape before sewing the shoulder seams or the side seams. After the bias tape was sewn on, I would sew the bias tape together with the shoulder and side seams as one single seam. That way if I had to alter the shoulder seams or the sides seams of the top, I only had to unpick a little bit of bias tape to get to the seams. This was a great plan until I thought about how I wanted to sew the bias tape on.

DSCN1298In deciding how I wanted to sew the bias tape on, did I want to sew the tape to the right side of the fabric and then fold it to the wrong side and stitch in the ditch on the front so that no seams were showing? Or, did I want to sew the tape to the wrong side and fold it to the right side and then stitch the tape with a decorated thread or stitch?

Since I was already mixing colors by using the pink bias tape on the purple top and visa versa, I choose the second option for sewing the bias tape on. So, my final sewing plan went as follows: I would sew the bias tape to the wrong side of the fabric and would then fold the tape to the right side after sewing the bias tape together with the shoulder and side seams. I would then top stitch the tape with the opposite color thread, i.e. sew the purple bias tape on with pink thread and visa versa. Sounds like a solid plan, right?

Well, this did not work as planned.

DSCN1295Because of how I had sewed the bias tape on, when I folded it to the right side the bias tape was needed to be sewed together opposite of the shoulder and side seams. If I had sewn the bias tape the other way that I had thought about doing it and folded it to the wrong side, my seams would have worked. But, instead of my plan working, I got to unpick several inches of each piece of the bias tape so that I could sew the bias tape together, then I could sew the shoulder and side seams together and then sew the bias tape back in place on the wrong side. Finally, I could fold the bias tape to the front and do the top stitching. All these little seams were flustering and extremely time consuming to sew and lets face it, not a lot of fun to do! But, I finally got it done and I had completed the sewing of the first top.

DSCN1306I wanted to sew the second top with the bias tape folding the same way as the first so I returned to the pattern’s instructions. I started by sewing the shoulder and side seams together first and then I sewed the bias tape on the wrong side of the top. Next I folded the tape to the right side and then top stitched the tape on. This went much faster and easier than the sewing of the first top had with no little seams to deal with. An with that the second tops sewing was complete.

I had four opportunities to learn the best way to start and stop the bias tape. I tried several ways but the way that folded and stitched the best for me was to leave a small piece of bias tape unstitched where I started. When I reached the end of the seam for the bias tape, I folded the ending piece of bias tape back on itself. I then laid the starting unstitched piece on top of the folded ending piece and then sewed this in place. When I folded the bias tape over, the starting pieces folded into the folded ending piece to make a finished start and stop of the bias tape.

DSCN1313The idea of sewing the bias tape to the wrong side of the top and then folding the bias tape to the front and top stitching in a contrasting thread sounded great, but in reality, sewing the bias tape on the right side and folding it to the back and stitching in the ditch with a matching thread would have hid a lot of sewing sins.

The top stitching looks good for the most part, but anywhere were my seams were not exactly straight, the contrasting thread announces the wavy seam LOUDLY. Also the starting and stopping of the seams don’t look that good. This is especially true where I was learning how I wanted to start and stop the bias tape.

DSCN1299The sewing of the tops would have been a lot easier and cleaner if I had sewn the bias tape the other way, sewn to right side and then folded to the back. I also could have followed my fitting plan. But, I had sewn the bias tape the other way and many lessons were learned, so it made the whole experience a good thing. Plus, the tops were looking good with the contrasting colors and threads. So, with the tops sewn, it was time to add on the buttons and buttonholes.

Join me next time to see how they turned out once they were completed!

Until then, sew forth and bias tape on!

Being Biased – Part 1 -The Making of the Bias Tape

IMG_1621My coworker’s tween girls are using and enjoying their Dr Who bags and it does my heart good for someone to enjoy and use something that I have made.

So much so, that it was easy to find another pattern to sew for them next. This time I made them a summer crossed back top from some sugar skull fabric that they picked out. I found this crossed back top pattern on line for free. It looked like a fun summer shirt, easy enough to sew and the right size for the girls.

I gave the girls their choice of a couple of fabrics that I had in the stash and they both picked the sugar skull fabric. I did not have enough sugar skull fabric to made both shirts so I planned to piece the tops with some black fabric from the stash.

Then I thought about it being summer. DSCN1296These were summer tops made to be worn in the heat of the summer months, so how could I make them from black fabric? So I dug through the stash and I found some nice pink and purple that would match the sugar skull fabric.

I decided to make one top from the pink and one from the purple so the girls would not have to match. I know that teens are image concious that way. The pattern is only two pieces, a front and a back, cut twice. Based on the girls measurements, I cut the front and back 1/4 inch wider and 1 inch longer than the pattern called for. The pattern also called for 3 yards of 1/2 inch double folded bias tape. I

f I had been making the tops with the black fabric, I would have bought the needed bias tape, but since I was using the pink and purple fabric, I decided to make the bias tape. 61NeRAwqLEL._SY450_Then I had the idea of using the pink bias tape on the purple shirt and the purple bias tape on the pink shirt to give them some great contrast, so I would definitely be making the bias tape myself. Plus, it would give me the opportunity to make bias tape again, and as you know practice makes perfect and I don’t use bias tape all that often.

Now, I thought I had the process down for making bias tape from the last time I made it for another project, but I was incorrect. I had a lot to learn and relearn while making this bias tape. I started out by cutting 1 inch strips on the bias. When it came time to sew the bias strips together, I knew that they needed to be sewn at a 90 degree angle, but I kept sewing the strips together backwards, one seam up and then one seam down. After much trial and error, I figured out that I needed to sew one strip on top, then the next strip on bottom to keep all the seams all on one side. 71f-MxnZmTL._SY450_

After getting all the bias strips sewn together correctly, I started to iron and shape them. I used my 1/2 bias tape maker and was making some beautiful bias tape, when I realized that my bias tape was only single fold.

What? Darn! I needed double folded bias tape!

So I folded my beautiful 1/2 single fold bias tape in half and got 1/4 inch double folded bias tape, half the size of what I needed. Crap! I seriously thought about just using the 1/4 inch double fold bias tape that I had made but I decided against it and started all over again.

This time, I cut 2 inch strips on the bias, sewing them together correctly as I had learned to do earlier, and I prepared to iron again, but not until I purchased a one inch bias tape maker.

Looking on Amazon for bias tape makers, I found two types, Singer brand made completely from metal, and several third party brands made of metal with a plastic insert.

Which was better? DSCN1310

After reading many reviews and pondering the question, the husband rolled his eyes and ordered me both the Singer and another brand with the plastic inserts. After trying both styles of bias tape maker, I decided to use the Singer metal ones. Even though both worked fine, I just liked the Singer ones better. They seem to fold the fabric more evenly and were easier to push the fabric into the maker when starting out.

After a fair amount of ironing, I had 4 yards of 1/2 inch double folded bias tape in both pink and purple, ready to sew on. I made 4 yards of each color rather than 3 yards like the pattern called for because I had increased the size of the tops slightly from what the pattern called for.

Now it was time to sew the bias tape on to the tops.

Stay tuned for the construction of the crossed back summer tops in my next post!

Until then, sew forth and bias tape on!

Simplicity 2480 – The Jacket – Part 4

DSCN0984With the pockets now completed, it was finally time to stitch the jacket! The first step was to insert the zipper. Remembering the lessons that I had learned from inserting the zipper in the little girl’s peplum jacket, this zipper sewed in much easier. And I did not need to move the needle over to sew the zipper on like I did the last time. The only challenge I faced with this zipper was deciding just how long I wanted the zipper to be.

Did I want it to extend into the collar or stop just before the collar? DSCN0807

The pattern called for the zipper to be inserted into the collar, but If I stopped the zipper at the collar, I could attach the collar as I would the collar of a camp shirt, finishing it off with a little twill tape.

If I followed the pattern instead and inserted the zipper into the collar, some hand stitching would be required to finish the collar. Now, you know how much I just “love” hand stitching, so you can guess which plan I was leaning towards, but then I remembered that I was making this jacket to learn so I decided to follow the pattern and insert the zipper into the collar, and then do the required hand stitching. After sewing on the zipper and facings, I hand stitched the edge of the collar to the back of the jacket. This went a lot smoother than I expected it to. I think I did a pretty good job on the hand stitching and that it will hold up with wearing.

Now that it is done I am pleased with the results of how I attached the zipper, collar and facings. DSCN0737Before I started this pattern, I read some pattern reviews for this pattern on the internet and one of the things mentioned about this pattern was that the sleeves were extremely wide. I could see this as I traced the sleeve part of the pattern, so I decided, based on the size of my wrists, to grade 4 inches out of the the width of the sleeves starting at the wrist.

I think the wearer of this jacket will like the thinner sleeves and it saved on fabric. I inserted the elastic at the bottom of the sleeves as the pattern called for. I think that will also help with any extra blousing from the wide sleeves. DSCN0989I interfaced the facings and collar before sewing them on. I just grabbed the first interfacing that I pulled from the stash to use, but I wished later that I would have looked a little closer.

Now, with the interfacing applied and the jacket sewn up, the interfacing that I used is too heavy for the fleece. The heavy interfacing makes the collar stiff so that it only wants to stand up. The heavy interfacing is also a problem at the inseam pockets. Because I used two pieces of fleece to make the pockets, they are already bulky but when I added the heavily interfaced facing on top of the pockets at the bottom of the jacket by the zipper, it is even bulkier.

Lesson learned. DSCN0987

Upon completion, I stared at the jacket and it looked very odd to me. It looked like it would never fit anyone.

It’s was so small in circumference but long in length in both the sleeves and the body of the jacket. Who would have such odd body proportions. Then it dawned on me what I had done. I had made a extra small adult jacket, and not an extra large child’s jacket. Once I figured this out I could finally picture a young slender adult wearing this jacket without any problem. An unforeseen lesson in sizing and fit was learned this time around. Although this jacket may not be perfect, and some of the seams are not very straight, I am still pleased with the end results.

I learned a lot, and it has left me with several ideas and sewing techniques that I want to try and work on in the future. I hope some one will enjoy wearing this jacket and that it will fit them well.

Until next time, sew forth and jacket on!

Simplicity 2480 – Pocket #3 and #4 – Part 3

Version 4As mentioned in a previous post, I had already decided not to make the side in seam pockets with a zipper closure as the pattern had called for, so I set the pattern guide aside and thought up my own plan for sewing these pockets. Most of my ideas came from the in seam side pockets I had sewn in a little kid’s polar fleece jacket several years ago but with a few changes.

The pockets on the kid’s jacket were just one piece which was sewn to the front of the jacket to make the pocket. An open rectangle was sewn at the side seam for the opening of the pocket and then the pocket sewn to the front of the jacket to complete the pocket. The seam attaching the pocket to the jacket was seen on the front of the jacket.

DSCN0768The pattern I was currently working with called for these pockets to be make from two pieces so the pocket is not sewn to the front of the jacket. I liked the idea of not having a visible seam on the front of this jacket. So, to make the opening of the pocket, I placed one piece of the pocket on the front of the jacket, right sides together and sewed, cut and turned the rectangle for the opening. Next, I sewed the second pocket piece to the first pocket piece to complete the pocket.

DSCN0802 (1)The pattern called for the first piece of these pockets to be a lining fabric instead of using two pieces of the fleece. The reason for this was the bulk. It you were using a heavy polar fleece, two pieces would be very bulky, but I was not using polar fleece, my fabric was just a sweatshirt fleece, so I made both sides of these pockets with the same fabric. Two pieces of the fleece didn’t seem that bulky to begin with, but when it was added to a third piece, the front of the jacket, the pocket was then getting a little bulky. It was not so bulky that I was willing to unpick and restitch the pockets but the lesson was learned. Don’t double up fleece when making pockets with it!

With pockets #3 and #4 done now it was time to insert the zipper and finish up the jacket. That’s coming up next so stay tuned.

Until next time, sew forth and in-seam pocket on!

Simplicity 2480 – Pocket #2 – Part 2

Version 3I’ve sewn patch pockets before, so I did not pay much attention to the pattern guide as I sewed on the front patch pockets of this jacket, but when it came to the zippered front pocket, I read and studied the pattern guide throughly. When all was said and done, I wish I had not. Let me explain why.

Per the pattern guide instructions, I traced the cut lines for this zippered pocket onto a piece of interfacing and ironed it to the front of the jacket. Next, I cut on the cutting lines. The next step was to sew the shortened zipper to the small pieces that were made by the cutting lines. Because the pieces were very small, and the zipper was bulky and the fleece had stretch to it, this was not easy. It was difficult to sew a nice straight seam. I worked through it though and finally got the zipper sewn to the front of the jacket.

DSCN0753The next step was to sew the pocket to the zipper. Once again this proved to be a challenge. I had to sew the pocket to the zipper tape and the small cutting line pieces as I held the rest of the jacket out of the way and worked through the bulk and the stretch. My seams were not straight or even on this pocket but I finally finished it. The finished pocket is far from perfect, but it does not look too bad so I decided to call it done.

The reasons that I decided to call this pocket good enough for now was that I had no intentions of sewing another zippered pocket this way again. As I struggled to sew this pocket together, my thoughts drifted to what I had read about welt pockets. Wouldn’t it be easier to have sewn this pocket on like a welt pocket? Yes, I think so.

DSCN0756When I sew another zippered pocket, I will approach it as a welt pocket. I will sew the pocket to the front of the jacket, cut the cutting lines, and turn the pocket to the inside. This will give me a nice rectangle for the zipper. Instead of folding the pocket fabric into a welt at this point, the zipper will be top stitched to the rectangle, then the pocket fabric will be sewn together on the inside as if the welt had be formed and sewn in place.

DSCN0759I’m anxious to try the zippered welt pocket sewing plan that I have thought up to see it my ideas are valid. So, for about one second I did consider taking off the patch pocket and adding another zippered pocket instead. Then I remembered the liquid seam that I had used to finish the patch pocket and decided to leave the patch pocket alone and continue on with the rest of the jacket. My zippered welt pocket plan would have to wait for another project. And with that, it was time to sew pockets 3 and 4 to this jacket, the in seam side pockets. So, stay tuned to see how they turned out in the next post.

Until then, sew forth and zipper pocket on!