Tag Archive | top

Creative Determining – Part 2

DSCN3986DSCN3987To begin the the sewing process of the Snoopy peplum top I started with the peplum first.

Since I was not going to line the peplum, I wanted to hide all the seams as much as possible, so I sewed French seams to piece the peplum together.

 

This was not difficult, just time consuming with a lot of ironing in between seams. I did a simple 1/2 inch hem at the bottom of the peplum to complete it.

Sewing the bodice was next. I decided at the last minute to add the yellow sleeves to the top. I like the yellow sleeves but as I snipped the curve of one of the sleeves I caught the lining and so I had to do a little mending. Luckily, the mended spot is on the inside of the top and cannot be seen from the outside. It should not affect the wearing of the top.

DSCN3998DSCN3989After gathering the peplum, I sewed the peplum to the bodice, making sure to line up the seams as much as possible. I serged this seam to finish it, rather than covering the seam with the lining and doing the stitch in the ditch seam.

The serged seam looks fine and saved me the headache of doing the stitch in the ditch seam.

 

I probably could have used the practice sewing the stitch in the ditch seam on this top, but sometimes just sewing the easy and simple way is fun too. And it’s much less stressful too!

With that, the little girl’s peplum top from the leftover Snoopy fabric scraps was completed!

DSCN3995DSCN3994The top is just adorable and the multiple seams in the peplum are really not that noticeable with the gathers.

This was a fun sew.

It is always fun to make something from nothing and to let the creative side flow to make it work.

Unfortunately, now that I have used up all the Snoopy scraps, I have at least a hundred projects that have raced through my mind that I could have made using the scraps.

Having said that though, I am not disappointed at all that I used these Snoopy scraps to make this top and at least they were put to good use!

Until then, sew forth and determine on!

Creative Determining – Part 1

DSCN3986There was no way that I was going to throw away any of the precious Snoopy fabric scraps left over from my new Snoopy shirt. The scraps really were not large enough to make anything with, not even for a child, but I just could not bear to throw them away. So, what to do with these scraps beside stack them on the edge of the cutting table and stare at them?

Recently, I have seen several little girls peplum tops that are just adorable and I have wanted to make one. So, looking at the Snoopy fabric scraps, I decided to see if I could squeeze a little girl’s peplum top out of the pieces. The size of top I would make would be determined by the dimensions of the scraps.

DSCN3813I didn’t really have a pattern so I turned to the internet for ideas. The first style of peplum top I found had a circular peplum. This was out of the question. The scraps I had to work with were absolutely too small to cut a circular peplum from. The second style I found was a gathered peplum. Hmmm. I might be able to make this work with the scraps.

DSCN3985Now, how long should the peplum be versus the length of the bodice? I saw a variety of bodice and peplum lengths from long bodices with short peplums to short bodices with long peplums and many hi/low peplums in between while I was searching. Once again, I would need to let the dimensions of the scraps determine the length of the peplum and the bodice and the scraps would also determine how full the gathered peplum would be.

DSCN3999Still not having a pattern, I pulled out my favorite little girls dress pattern as a guide. Based on the size of the largest scrap, I determined that I could get a size 4 bodice front and back from the scraps as well as have a few pieces left over for the peplum. I quickly picked some yellow cotton from the stash that matched Woodstock for the lining of the bodice.

To make the peplum, I squared the remaining scraps of Snoopy fabric I had and found that I had two pieces approximately 6 inches tall by 12 inches wide and 4 pieces that were 6 inches tall by 6 inches wide. (Actually, one of the 6 by 6 inches pieces was only DSCN39965 inches wide, but I could work with that.) With a lot of seam work, I determined that I could make these scraps work out for the peplum. I would sew the two 12 wide pieces together for the front of the peplum and sew the 6 inches pieces together for the back or the peplum.

I would not be matching any of the designs in the Snoopy fabric. There was certainly not enough scraps for that, but luckily with a gathered peplum, the non-matching designs as well as the many seams that I would be sewing would just be gathered in.

Excitement for this project grew, as I saw my almost useless scraps become a little girls peplum top!

Stay tuned for the sewing of the little girl’s Snoopy peplum top.

Until then, sew forth and scrap on!

Time To Say Goodbye, and Hello!

DSCN3535DSCN3537“He’s dead, Jim!” goes the often quoted line from Star Trek’s ever present with a quip Doctor “Bones” McCoy. And in this case, it’s as true as ever…

My favorite Snoopy shirt, made so many years ago, is finally dead. It is faded, thread bare and as of the last laundering, has a small hole at the back of the neck.

But at least I can say I have wore it everywhere!

 

It’s been to London, it’s been to France, and yes it’s even seen the Queen’s underpants! Well Elton John’s anyway! It been wore to work, at home, for parties, on vacations, just everywhere! But I can no longer wear it outside of the house in public again in this shape.

But for some reason I just can’t seem to stop wearing it!

It’s my SNOOPY shirt you see, and I just can’t seem to let it go…

So, to ease the pain of my not being able to wear this particular Snoopy shirt in public again, I decided it was time to open the box of my most precious fabrics, the Snoopy fabrics, and to use some of it to make me a new Snoopy shirt.

DSCN2792Luckily I did not even have to open the precious Snoopy fabric box to pick out the piece of Snoopy fabric that I would use to make this new shirt from as I had just purchased it at Walmart a couple of weeks ago and it hadn’t even made it to the box for storage yet.

I then debated about the style of shirt that I wanted this new Snoopy shirt to be.

Collar or no collar? Buttons or no buttons?

DSCN3447After making my last project, the fleece football pull over jacket, I decided to make this shirt in that style, but with no hood and just short sleeves.

I would use my basic t-shirt sloper pattern, but I would cut a slit in the front to get the shirt over my head and use facings to complete the neck line.

This would be a very simple design that would let the Snoopy fabric be the details of the shirt.

I had never made myself a shirt like this before, but it didn’t seem like it would be too difficult to make the changes to the pattern or to sew it up.

DSCN3541It was easy enough to prep this fabric for cutting, make the alterations to the pattern and lay it out, but when it was finally time to cut the fabric, panic and fear filled my heart and soul…

I would be cutting into this precious Snoopy fabric and what if I ruined it?
What if I cut it wrong?
What if I didn’t like the pullover design?
What if I messed up the alterations?

DSCN3539I could not cut into this fabric.

I just couldn’t.

So I decided that I would not be making myself a new Snoopy shirt after all, and that I would never, ever have another Snoopy shirt again.

SIGH!

But to console myself, I would always know that I had a box filled with Snoopy fabrics that I could sometimes visit and look longingly at behind it’s bulletproof glass in it’s hermetically sealed climate controlled room.

As I was folding up the Snoopy fabric to put it back in the box, the husband wandered into the sewing room to see my progress. I explained to him that I just could not cut into my precious Snoopy fabric so there would be no new shirt. He sympathized with me and I was done sewing for the day.

The next day, the husband made a secret trip to Walmart and bought me some more of the same Snoopy fabric. He explained that now I could make my new Snoopy shirt as planned and I would still have some of this Snoopy fabric carefully tucked away in the Snoopy fabric box.

AAUGH! Isn’t he the best?

DSCN3542Well back to work on the new shirt then!

Cutting out this shirt went smoothly. The sewing of this shirt also went smoothly. I carefully stitched and cut the the slit and sewed the neck with the facings.

I did put a small bar tack at the base of the slit to stabilize the slit. I thought for a moment about tacking the slit open, and maybe adding some buttons, but then decided not to. And soon enough, I had a new Snoopy shirt to wear!

YAY!

DSCN3543This newly designed Snoopy shirt has passed the “wear test” with flying colors!

This shirt is very comfortable to wear and I like the design and the slit. It’s very hospital scrub like in design.

And, everyone loved the Snoopy and Woodstock’s on the shirt. I am so happy that I made this shirt and that it turned out so well!

And I am especially happy that I have more of this fabric tucked away in the stash to use for something else later on.

The success of this shirt MAY just have encouraged me enough to pull another piece of Snoopy fabric from the box and make another shirt from it. I might even use a fabric that can not be replaced readily.

Maybe! That’s a BIG MAYBE! We’ll see.

Until then, sew forth and Snoopy Happy Dance on!

WWWHHHAAATTT!?! – The Minions – Part 2

DSCN2582I had already spent the appropriate amount of time worrying about making this minion shirt so it was easy to get started on it.

I really wanted this shirt to sew together without any problems, so I decided to take my time and think things through carefully. So after laundering and ironing the fabric , it was time to start cutting.

I cut very carefully and added the alterations that I wanted to the pattern as I cut. I was quite selective about the interfacing I chose to use and I went ahead and cut it out too.

DSCN2584As I started to sew, I realized that I did make one cutting/design error, well not really an error, but a small change to the design. In my mind, the shirt had the minion fabric on the right and the blue on the left, but I had cut the left front from the minion fabric and the right front from the blue fabric. Mmmmmm, was this going to look ok? After much thought, I decided it would look fine, and maybe better because the buttons would be on the solid blue fabric instead of lost in the the minions fabric.

DSCN2581The sewing when smoothly. I took my time and tried the shirt on after each step. I also ironed each seam carefully as it was sewn. As I serged the edges of the sleeves, preparing them to be hemmed, I did not notice that I I was running out of thread on one of my loopers. Once the looper ran out of thread, my serged edge was ruined. Luckily, I had debated about cutting 1/2 inch off the length of the sleeves and had not done so yet. So, I cut the 1/2 inches off the length of the sleeves ridding me of the bad serged edge, threaded new spools of thread on my loopers and serged the new edges.

With the sewing on of the final button, I declared the shirt done and tried it on. The fit seemed to be good, but as I looked at myself in the mirror, the shirt needed to be something else. The right blue front was just that, blue. I grabbed some scraps and started adding to the blue front piece.

DSCN2493At first, I wanted to add a stripe of minion fabric down the blue front, but that was too much of an accent. I thought about digitizing a minion embroidery design. But since I was too excited about wearing the shirt, and it would take time to perfect the design and I wanted to wear the shirt now. My next thought was a pocket. This would not be a functioning pocket, just something for show, so it would not have to be any certain size or style. I decided to make a temporary pocket and see how it looked pinned on.

DSCN2496To make the pocket, I cut out two squares of fabric and then rounded the corner on one end. Next, with right sides together, I sewed completely around the two modified squares. Next, I made a small cut in the fabric that would be inside the pocket. I turned the pocket right side out through this slit. After a lot of pressing, with a little seam to seam, I mended the cut that I made in the pocket to turn it inside out. This worked well and I had a finished pocket. Since I will not be putting anything in this pocket, I am not worried about the seam to seam mending holding up with wear and tear.

Placing the pocket on the blue front, I liked it, then with another look, I did not, then after a few minutes, I liked it again.

Argh!

DSCN2498I turned to the husband for his opinion and he said that he did like the pocket, so I sewed the pocket to the front of the shirt. I am still up in the air as to wether I like the pocket or not but it is sewn to the shirt for now.

The shirt has passed the “wear” test and I really like it. My alterations seem to be good. This shirt is fun to wear and is very comfortable.

It also makes me crave bananas for some reason…

Until next time, sew forth and banana on!

WWWHHHAAATTT!?! – The Skulls – Part 1

Despicable-me-minions-480x477Its what I want for Christmas. I told the husband that all I wanted for Christmas this year was a minion. Now, not one of those little ones from McDonald’s or a plush one, or even one of those plastic ones that talk. I wanted a really live, living, breathing minion. And, of course, I don’t want my minion to be lonely while I’m at work so I had better have a couple of minions. The husband said he would see what he could do but in the meanwhile I decided to satisfy my minion need with some minion fabric.

When I saw the minion fabric at Walmart, I knew that I just had to have it. I had absolutely no idea what I was going to make from it, but I just knew that I must have some. I purchased 1 yard and brought it home. The fabric sat on the cutting table while I debated what I wanted to make from it. I thought about all kinds of fun kid’s clothes that I could make from it, but instead I only wanted it for myself, so I decided to make myself a shirt from it.

Because let’s be honest here… Who doesn’t need a minion shirt?

DSCN2591Before I could cut into the minion fabric, I found myself fabric shopping again when I ran across this banana fabric. Seriously, it was bananas! BANANA! So of course, I needed some banana fabric to go with my minion fabric so I purchased one yard of the banana and headed home. Once I was home, I placed it next to the minion fabric on the cutting table. And I thought I was all ready to go. But, before I could cut into the minion fabric or the banana fabric, I found myself scoping out Walmart’s fabric department again, only to find a different minion fabric that I liked better for my shirt than the first minion piece, so one yard of this second minion fabric made it way to my cutting table as well.

DSCN2586Finally all set and before I could go fabric shopping again, I decided it was time to design and make my minion shirt. I quickly decided to make one front from the second minion fabric that I had picked up, the collar and sleeves from the banana fabric and then to find some blue in the stash for the other front side and the back. After laundering and ironing the fabric, I pulled my sloper pattern from the closet, only to remember that I was in the process of altering my basic sloper.

Augh!

I did not want to cut into my precious minion and banana fabric with a pattern that needed it’s alterations tested.

DSCN2585So, I folded up my minion and banana fabric and pulled some fabric from the stash to test my alterations on. I like the colors of this fabric a lot but it has not become a shirt till now because it is very thin. I was skeptical of how it would wear being so thin, but I decided that since this was a test shirt, I would go ahead and use this fabric to give it a try.

So I cut out my altered pattern and I started to sew it up.

The sewing went smoothly. I was afraid that my machine would argue about sewing this thin fabric but all went well, and soon it was time to sew buttonholes and buttons. Sitting on the top of my button box was some sugar skull buttons that the husband got me awhile back when I needed skull buttons for the girl’s cross back tops. I laid the buttons out on the shirt. They did not really match but they looked fun, so why not. Again, this was just a test shirt.

DSCN2589Rather than picking out just one design of sugar skulls, I sorted through the pack of buttons and picked five different designs. When I sewed the buttons on, each button had its holes in a different spot. One button’s holes were vertical, one was horizontal, and the others were at a variety of angles. This presented a challenge to sew the buttons on straight. I had to measure and turn the fabric every which way to keep the skulls on the buttons right side up. Luckily with some patience and time, I got the buttons sewn on correctly.

DSCN2590I have had a chance to give this shirt a “wear test” and it passed just fine. There were a couple of small alterations that are needed to the armscye and button placement but I had solved the fitting problem at the neck from my last shirt made from this pattern.

But the good news is that I feel good enough about my alterations to my pattern to start the minion shirt as my next project.

Until then, sew forth and BANANA on!

Being Biased – Part 3 – Button Fitting

DSCN1300I believe I have fallen in love with bias tape.

Even though, I had a number of trial and tribulations in the making of and the sewing on of the bias tape with these tops, I can see were bias tape can be a fun accent to many sewing projects and I can’t wait to start another bias tape project.

But before I do that I needed to finish these cross back summer tops before the summer has ended so that the girls can actually get some use out of them.

All I needed to do to finish them was to add buttons and buttonholes to the back of the tops and they would be done and ready to wear.

Sounds easy enough, doesn’t it? Well, I wish would have been as easy as it sounded.

DSCN1303I knew when I cut this pattern out that this pattern does not have a true side seam. I did not think it was going to be a big deal, but it was!

The backs are cut so that the shoulder and side seams are towards the front of the top. There is no seam directly under the armscye or on the shoulder. It is just to the side of the armscye and front of the shoulder.

This pattern also has no indication of where the buttonholes should be placed. So, when it came time for me to determine where to sew the buttonholes and buttons, I had some guessing to do. DSCN1304

I started the guessing by trying to determine where the true side seam would have been on these tops. Should the back come towards the front of the top a little, like 1/2 inch, or a lot, like 2 inches.

Next, I had to determine if the cross over should match at the top and leave a big “V” at the bottom of the back or should the “V” of the cross over be smaller by lowering the top. I spent hours measuring, folding, pinning, and deciding where to put the buttons and buttonholes.

I would think that I had it all ready to sew, then I decided that it wasn’t right and I would start again. After awhile even the husband grew tired of me showing him each variation that I tried. He tried to help, but I just could not make up my mind if I had it right or not. DSCN1302

Finally, I reached a point were I truly believed that I had it measured, folded and pinned where I wanted the buttons to be so I went to the sewing machine. I carefully sewed the buttonholes and buttons in place on both tops.

When I was done, I was quite pleased with myself until I held the tops up and the back curve of the cross over flopped down over one of the special buttons I had paid a lot of money for. Crap! The buttons needed to be higher on the top.

Now, how was I going to fix this? Version 2

My first thought to solve this problem was to sew a hook and eye to the curve which would attach the curve to the back of the top. This would keep the curve from flopping over but that did not work. When the curve tried to flop over, you could see the hook and eye and it looked worse than the flopping curve of the fabric.

My next thought was to use some velcro. As I went to sew the velcro on, the husband asked what I was doing. I showed him the flopping curve and how I was trying to fix it. He said to stop. He said that since girls were sisters they could keep an eye on each other’s backs when they were wearing the tops and if the curve flopped, they could fold a crease in the bias tape so that the curve would not flop as much. This seemed like a reasonable solution to the flopping curve, so I left it at that.

20150530_124144The REAL answer to this whole problem was to have the girls try the tops on before I placed the buttons.

I could have quickly determined where the “side” and “shoulder” seams should be, how big the “V” in the back should be and where the buttons needed to be. But, I had wanted the tops to be a surprise for them so I didn’t. Even though they had picked out the fabric, they did not know what I was making from it. Plus, with them not knowing what or when I was making something, there was less pressure to get the tops completed.

With that all in mind, I determined that the surprise and less pressure to get the items completed were not worth the button/buttonhole headache, and with this lesson learned, the next time I make something for the girls, there will be fittings during the process. Version 2

Upon receiving the tops, their mom says the girls like them and will wear them. I explained to their mom the button/floppy curve issue and she said it would not be a problem.

I don’t believe that the girls were nearly as excited about these tops as they were their fun vests or their Dr Who bags, but that is ok because I learned a lot from these tops both in the sewing process itself and in the process of sewing for others. 20150530_124000

And the next time I sew for the girls, I am getting them involved in the process.

No more surprises!

I want them to pick their own fabrics, colors and styles. I want to measure them so that I have the best fit, instead of using a year old measurement that their mom took (no offense to their mom), and I want fittings and alterations done during the sewing process.

I think I will learn even more sewing for them this way and they will have exactly what they want as well. Plus NO more guessing!

Until then, sew forth and bias tape on!

Being Biased – Part 2 – The Sewing of the Bias Tape

DSCN1308I gave the process of sewing of the crossed back summer tops a lot of thought before I made the first seam.

I had read the pattern instructions, but I wanted to sew the top together with fitting in mind. I wanted to sew the seams so that the minimal amount of unpicking would be necessary if I needed to alter the size of the tops for the girls later. So, my plan was to start with sewing on the bias tape before sewing the shoulder seams or the side seams. After the bias tape was sewn on, I would sew the bias tape together with the shoulder and side seams as one single seam. That way if I had to alter the shoulder seams or the sides seams of the top, I only had to unpick a little bit of bias tape to get to the seams. This was a great plan until I thought about how I wanted to sew the bias tape on.

DSCN1298In deciding how I wanted to sew the bias tape on, did I want to sew the tape to the right side of the fabric and then fold it to the wrong side and stitch in the ditch on the front so that no seams were showing? Or, did I want to sew the tape to the wrong side and fold it to the right side and then stitch the tape with a decorated thread or stitch?

Since I was already mixing colors by using the pink bias tape on the purple top and visa versa, I choose the second option for sewing the bias tape on. So, my final sewing plan went as follows: I would sew the bias tape to the wrong side of the fabric and would then fold the tape to the right side after sewing the bias tape together with the shoulder and side seams. I would then top stitch the tape with the opposite color thread, i.e. sew the purple bias tape on with pink thread and visa versa. Sounds like a solid plan, right?

Well, this did not work as planned.

DSCN1295Because of how I had sewed the bias tape on, when I folded it to the right side the bias tape was needed to be sewed together opposite of the shoulder and side seams. If I had sewn the bias tape the other way that I had thought about doing it and folded it to the wrong side, my seams would have worked. But, instead of my plan working, I got to unpick several inches of each piece of the bias tape so that I could sew the bias tape together, then I could sew the shoulder and side seams together and then sew the bias tape back in place on the wrong side. Finally, I could fold the bias tape to the front and do the top stitching. All these little seams were flustering and extremely time consuming to sew and lets face it, not a lot of fun to do! But, I finally got it done and I had completed the sewing of the first top.

DSCN1306I wanted to sew the second top with the bias tape folding the same way as the first so I returned to the pattern’s instructions. I started by sewing the shoulder and side seams together first and then I sewed the bias tape on the wrong side of the top. Next I folded the tape to the right side and then top stitched the tape on. This went much faster and easier than the sewing of the first top had with no little seams to deal with. An with that the second tops sewing was complete.

I had four opportunities to learn the best way to start and stop the bias tape. I tried several ways but the way that folded and stitched the best for me was to leave a small piece of bias tape unstitched where I started. When I reached the end of the seam for the bias tape, I folded the ending piece of bias tape back on itself. I then laid the starting unstitched piece on top of the folded ending piece and then sewed this in place. When I folded the bias tape over, the starting pieces folded into the folded ending piece to make a finished start and stop of the bias tape.

DSCN1313The idea of sewing the bias tape to the wrong side of the top and then folding the bias tape to the front and top stitching in a contrasting thread sounded great, but in reality, sewing the bias tape on the right side and folding it to the back and stitching in the ditch with a matching thread would have hid a lot of sewing sins.

The top stitching looks good for the most part, but anywhere were my seams were not exactly straight, the contrasting thread announces the wavy seam LOUDLY. Also the starting and stopping of the seams don’t look that good. This is especially true where I was learning how I wanted to start and stop the bias tape.

DSCN1299The sewing of the tops would have been a lot easier and cleaner if I had sewn the bias tape the other way, sewn to right side and then folded to the back. I also could have followed my fitting plan. But, I had sewn the bias tape the other way and many lessons were learned, so it made the whole experience a good thing. Plus, the tops were looking good with the contrasting colors and threads. So, with the tops sewn, it was time to add on the buttons and buttonholes.

Join me next time to see how they turned out once they were completed!

Until then, sew forth and bias tape on!

Being Biased – Part 1 -The Making of the Bias Tape

IMG_1621My coworker’s tween girls are using and enjoying their Dr Who bags and it does my heart good for someone to enjoy and use something that I have made.

So much so, that it was easy to find another pattern to sew for them next. This time I made them a summer crossed back top from some sugar skull fabric that they picked out. I found this crossed back top pattern on line for free. It looked like a fun summer shirt, easy enough to sew and the right size for the girls.

I gave the girls their choice of a couple of fabrics that I had in the stash and they both picked the sugar skull fabric. I did not have enough sugar skull fabric to made both shirts so I planned to piece the tops with some black fabric from the stash.

Then I thought about it being summer. DSCN1296These were summer tops made to be worn in the heat of the summer months, so how could I make them from black fabric? So I dug through the stash and I found some nice pink and purple that would match the sugar skull fabric.

I decided to make one top from the pink and one from the purple so the girls would not have to match. I know that teens are image concious that way. The pattern is only two pieces, a front and a back, cut twice. Based on the girls measurements, I cut the front and back 1/4 inch wider and 1 inch longer than the pattern called for. The pattern also called for 3 yards of 1/2 inch double folded bias tape. I

f I had been making the tops with the black fabric, I would have bought the needed bias tape, but since I was using the pink and purple fabric, I decided to make the bias tape. 61NeRAwqLEL._SY450_Then I had the idea of using the pink bias tape on the purple shirt and the purple bias tape on the pink shirt to give them some great contrast, so I would definitely be making the bias tape myself. Plus, it would give me the opportunity to make bias tape again, and as you know practice makes perfect and I don’t use bias tape all that often.

Now, I thought I had the process down for making bias tape from the last time I made it for another project, but I was incorrect. I had a lot to learn and relearn while making this bias tape. I started out by cutting 1 inch strips on the bias. When it came time to sew the bias strips together, I knew that they needed to be sewn at a 90 degree angle, but I kept sewing the strips together backwards, one seam up and then one seam down. After much trial and error, I figured out that I needed to sew one strip on top, then the next strip on bottom to keep all the seams all on one side. 71f-MxnZmTL._SY450_

After getting all the bias strips sewn together correctly, I started to iron and shape them. I used my 1/2 bias tape maker and was making some beautiful bias tape, when I realized that my bias tape was only single fold.

What? Darn! I needed double folded bias tape!

So I folded my beautiful 1/2 single fold bias tape in half and got 1/4 inch double folded bias tape, half the size of what I needed. Crap! I seriously thought about just using the 1/4 inch double fold bias tape that I had made but I decided against it and started all over again.

This time, I cut 2 inch strips on the bias, sewing them together correctly as I had learned to do earlier, and I prepared to iron again, but not until I purchased a one inch bias tape maker.

Looking on Amazon for bias tape makers, I found two types, Singer brand made completely from metal, and several third party brands made of metal with a plastic insert.

Which was better? DSCN1310

After reading many reviews and pondering the question, the husband rolled his eyes and ordered me both the Singer and another brand with the plastic inserts. After trying both styles of bias tape maker, I decided to use the Singer metal ones. Even though both worked fine, I just liked the Singer ones better. They seem to fold the fabric more evenly and were easier to push the fabric into the maker when starting out.

After a fair amount of ironing, I had 4 yards of 1/2 inch double folded bias tape in both pink and purple, ready to sew on. I made 4 yards of each color rather than 3 yards like the pattern called for because I had increased the size of the tops slightly from what the pattern called for.

Now it was time to sew the bias tape on to the tops.

Stay tuned for the construction of the crossed back summer tops in my next post!

Until then, sew forth and bias tape on!

What About The Scraps? – Part Two

DSCN2060The second set of scraps that were sitting on the cutting table that were not large enough to return to the stash were the pink fleece from the jackets I had recently made. This piece of fabric has already served its purpose in making two jackets, the little girl’s peplum jacket and the adult pocket jacket, but there was still enough scraps left over to make something else.

DSCN2061My first thought with fleece is always a sweatshirt, so that is what I decided to make with these scraps. Loving the white accents on the pink fleece of the adult pocket jacket, I decided to make a raglan sleeve sweatshirt and add white piping and white ribbing as an accent. I traced the pattern for a size 4 raglan sleeve sweatshirt from my Kwik-Sew book and I was ready to get cutting and sewing.

DSCN0863As I cut out the pattern pieces, it became obvious that I did not quite have enough scraps for a size 4 sweatshirt. I was only short by 1 inch or so on the sleeve length. Debating about cutting the pattern down to a size 3, I decided to stay with the size 4 pattern and just make larger cuffs. Maybe like me, the little girl that will wear this sweatshirt will have shorter arms and the sleeves will fit great instead of always being too long.

DSCN0866I used the white scraps from the pockets of the adult jacket and a thin cording for the piping. Using my machine’s zipper foot, I made the piping and then applied it to the sweatshirt sleeves. The sewing of the piping was a little time consuming, since I had to be careful to sew close to the piping but not sew into the piping, but was not too difficult. It was easy to pick another Smirk design to embroider on the sweatshirt and soon enough the sweatshirt was completed. And, it looks great! It is very cute. Plus, I don’t think that the bigger cuffs/shorter sleeves will be a problem.

DSCN0915I was so excited about the end results of the pink fleece sweatshirt, especially the piping portion, my creative mind went nuts and my next sewing project was quickly started. Using the same pattern, the size 4 raglan sleeve sweatshirt, the white fleece, although not a scraps, were quickly cut out. Red ribbing for the neck and black ribbing for the cuffs were cut out next. I grabbed some black denim scraps from my scrap pile for the piping and some larger cording from the closet and got started sewing.

DSCN2058There were no difficulties sewing the piping until it came time to sew the sweatshirt together. Because of the heavier denim fabric and the larger piping, it became a challenge to sew the ribbing to the neck and to sew the side seams together. Once I got these seams sewn, I had to finish the edges. I tried to use the serger but it was just too bulky. I finally used an overcast stitch on my sewing machine to finish the edges. Since the white fleece won’t fray, I think that the overcast stitch that I used will withstand the wear and tear from a 4 year old without any issues.

DSCN2066A Snoopy embroidery design was, of course, the design of choice for this shirt, but which one? Since the sweatshirt was simple basic Snoopy colors, I picked a simple basic Snoopy design, and I love the end results. Despite the bulky piping, the Snoopy sweatshirt is just adorable, and I learned several lessons about making and sewing piping on that I didn’t know before.

DSCN2059With these two sweatshirts completed, the usable scraps had been taken care of and the cutting table is now clear and ready for the next sewing project. Thank goodness! Waste not, want not.

Until then, sew forth and scrap on!

What About The Scraps? – Part One

DSCN2070I just love fabric! I love to hold it and feel it and measure it and imagine all the fun items that it could be made into. Then, I just love to fold it and hoard it in my stash until that special day when it finally is retrieved and made into something fun!

And that brings me to the age old question of “what to do with the scraps?”

After a project, should I fold up the scraps and return them to the stash or should they make their way to the donation box or the garbage? When I first started sewing, I saved every scrap, but over the years as the stash has grown in size, I have been more able to let go of and part with my scraps.

DSCN2071Now days, I evaluate my scraps based on a ranking system of importance.

1. Are there enough scraps left to make something with?

2. Did I enjoy working with the fabric?

3. How did the item wear when made from the fabric?

It was this evaluation that started my next sewing projects. DSCN2068

Left sitting on the cutting table were the scraps from my last few projects. I needed to clean off the table before I could cut out another project, so it was time to evaluate the scraps.

Large scraps were easily folded and returned back to the stash, but a couple of pieces were just not quite big enough to return to the stash. The first of these pieces was the scraps of purple and white knit left over from my last shirt.

The scraps were big enough to make something, so I did not want to just throw them away, and I enjoyed sewing with this fabric, plus my shirt has worn well, so I grabbed my Kwik-Sew books and I determined that I had enough scraps for a size 2 t-shirt with long sleeves. DSCN2072I already had the pattern traced, and in no time I had the pieces cut out and I was sewing them up.

To add a little something to this shirt, I top stitched the shoulder and sleeve seams. After sewing and serging these seams, I simple sewed the seam down from the top side of the shirt.

Looking at the results, I wish I had lengthened my stitches so it looked more decorative. I will do that next time. That was a good lesson learned.

IDSCN2069t was not hard to pick the Snoopy and Woodstock embroidery design for this little shirt. I worried that the embroidery design would be lost in the shell design of the shirt, but it did not once I had it stitched up. I think the embroidery design looks very cute and that it can easily be seen.

This little shirt was a fun and fast sewing project with fun results, plus the scraps were put to good use.

Hopefully, some little girl will enjoy wearing the shirt.

Stay tuned for the next scrap heap sewing project coming up soon.

Until then, sew forth and scrap on!