Tag Archive | twill

Girl’s Fleece Jacket (Done Backwards) – Part 2

DSCN2088When I started this jacket, I decided to go ahead add the optional cuffs to the sleeves.

The cuffs looked so cute on the jacket on the pattern envelope, that I wanted this jacket to have the cuffs. But when it came time to sew the cuffs on, they were not turning out very well. They were just too bulky. The cuffs are made from two pieces of fleece. The first piece is sewn to the sleeve, then the next piece is sewn to the first piece and then folded over to make the cuff. I cut out the cuffs, sewed the cuffs to the sleeves and then removed the cuffs. In my opinion, this was a bad design for a fleece cuff due to so many seams in the cuffs and the bulkiness these seams caused. There are four layers of fleece in the top seam of the cuff, and that is just too many layers of fleece.

DSCN2084If I wanted to keep the cuffs, I had to come with a solution, so I gave it some thought and came up with some ideas.

First, the sleeves could be cut longer to make the cuffs. This would eliminating the bulky seams, but I had not cut my sleeves longer so this solution was out for this particular jacket. Another solution would be to use a thin lining fabric as part of the DSCN2086cuff, but I did not have it in me to dig through the stash to find a matching fabric. My third solution was to skip the cuffs, and make more bias tape. I would finish the edges of the sleeves with yellow bias tape to match the pockets. (My first thought was to use the bias tape to finish the edge of the cuffs, but eliminating only one of the layers in the bulky cuff was not enough.) So, I choose this as my plan. This jacket would not have cuffs, and I would finish the sleeves edges with the yellow bias tape.

Thinking back, I could have had cuffs on this jacket by combining the solutions. I could have used a lining fabric and the bias tape to make the cuffs and eliminate the bulk. Hmmm. Maybe I will try that on the next jacket.

DSCN3414By using the bias tape on the sleeves, I did not have to worry about a hem or the fact I had not cut the sleeves longer to accommodate a hem. I applied the bias tape to the edges of the sleeves, trimmed the seams and turned the bias tape to finish the seams. I noticed that the thin bias tape looked weak at the bottom of the heavy sleeves. The way I got rid of this weak look was to not trim the seam inside the bias tape so much, which was different from any other time I have applied bias tape. Previously, when I applied bias tape, I wanted the seam allowance trimmed out before folding the tape over. If the seam allowance was left inside the bias tape this time, the look was much fuller and it looked better.

DSCN3418It was now decision time. Which way did I want the jacket to cross, left over right or right over left? After a lot of thought and debating, I decided to cross the fronts as if it were a boy’s jacket, the left front on top of the right front. This will probably drive the little girl that wears this jacket nuts as she tries to button the jacket backwards, but the half froggy’s that I got from folding the jacket the other way just didn’t look good. Hopefully whoever wears this jacket won’t mind the backwards buttoning buttons if it is a girl.

I was dreading making the buttonholes on this jacket. I was not sure how my sewing machine would handle sewing buttonholes on fleece. Sometimes, even with thin non-stretch fabric, my sewing machine has a mind of its own when it comes to making buttonholes and sews whatever it wants to. To help combat this problem, I made horizontal buttonholes, and held my breath as the buttonholes were sewn, but my sewing machine did great and the buttonholes turned out just fine.

DSCN3413If I had known then, at the beginning of the sewing of this jacket, what I know now, nearing the end of the sewing of the jacket, I would have added piping to the peter pan collar to coordinate with the finished design of jacket. It would have been really cute to have had the bright yellow piping around the collar to match the piping on the pockets and the bias tape on the sleeve. This is definitely something I will keep in mind for the next jacket.

DSCN3416With the sewing on of the last button, the jacket was finally done!

The making of this jacket was a learning experience from the beginning to the end, from the cutting of the fleece, to the sewing of a back facing, to the piping curved pockets to the designing of the fleece cuffs. There were many lessons learned on this fleece jacket.

All in all, I think the jacket is very cute and I hope some little girl will be willing to wear it and will enjoy it!

Until next time, sew forth and fleece on!

Girl’s Fleece Jacket (Done Backwards) – Part 1

DSCN3413Over the years, I have accumulated a massive amount of polar fleece in the stash. At first, these fleeces were only purchased with blankets in mind, but over time, my ideas for fleece fabric has expanded. So, when I saw this pattern, McCalls M4981, especially designed to be made from fleece, I knew what I wanted to sew next.

IMG_0002 (2)M4961 is a pattern for a girl’s unlined fleece jacket with a peter pan collar, patch pockets and buttons closures. I was excited to get started, but I quickly learned that this project was not going to be an easy sew or a fast sew.

To start, I selected a piece of fleece from the stash. I chose this cute girl’s design of froggy’s, bees and rainbows on a brown background. I did not have to launder the fabric before I got started since their was no preshrinking needed with this fleece. I traced the pattern, size 6, and got started with the cutting process.

DSCN2575Cutting out this jacket was not an easy or quick task. The print on this fleece was so far off grain that it was almost impossible to cut the pieces so the froggy’s and rainbows were standing up straight. I pulled the fabric and repositioned the pattern pieces until I finally got the pieces cut out. When I finally finished the cutting process, I realized I had lined up the right and left front backwards from each other.

DSCN2572When I folded the right front over the left front for a girl, I got a nice froggy edge on the right side and half of a froggy edge on the left side, but if I folded the front as you would for a boy, left front on top of the right front, then I had a nice froggy front. So, should I have a poor looking front with half froggy’s and cross the jacket for a girl or have a nice looking front and cross the jacket for a boy? That was the question. This question did not have to be answered right away so I decided to move on.

DSCN3411I did add some thin interfacing to the facings and the collar. The husband thought I was crazy for adding more bulk to the fleece, but I explained to him that was why I was using such thin interfacing. I just wanted something to stabilize the fleece at those spots and keep it from stretching while sewing, particularly when it came time for buttons and buttonholes.

DSCN2074To start the sewing process, I did not read the pattern guide at all. Looking at the pattern pieces, the sewing of this jacket seemed pretty straight forward, So, I just got started. Who needs directions anyway? Am I right? I sewed and pressed the collar, serged the facings edges, folded them over and sewed the facings to the collar. Normally, my next step would be to sew a piece of twill tape to the collars inside edge to finish it and then tacked the facings to the shoulder seams. This pattern has a back facing as well though, and I stopped for a moment as I pondered how I was supposed to sew it on. I then turned to the pattern guide and read that sewing the back facing to the side facings should have been the first step before adding the collar.

Too late now!

DSCN3410I was certainly not unpicking all my sewing that I had done up to this point. My first instinct was to grab my twill tape and just throw away the back facing but then I came up with plan to attach the back facing. After some tedious sewing, I got the back facing sewn on, only to find out that I had sewn it on backwards. The wrong side of the fleece was facing out. Augh! There was no way I was unpicked the back facing just to flip it over. It would just remain backwards. Sometimes, just when you think you know it all, and you certainly know better than some pattern maker and you get ahead of yourself, you find out too late just how wrong you are…

DSCN2080When it came time to sew the pockets, I debated about how to get nice smooth curved pockets since the use of the iron was of limited use with the fleece. I had read about using piping to help curve the pockets so I decided to give it a try. I cut bias strips from yellow cotton scraps and made the piping for the pockets. When it came to sewing the piping to the pocket, I was having trouble starting the bias tape in the fold of the pocket because of the bulk of the fleece. I turned to some liquid stitch for help. I folded the yellow fabric over the top of the cording in the piping and glued it down with the liquid stitch. This gave me a finish at the top of my piping so I did not have to keep tucking it into the fold. I did the same thing at the other end of piping on the other side of the pocket.

DSCN3409I don’t know if I really like the look of the piping at the top of the pockets done this way but it is fine for this time. I think I need to read more on how to start and stop the piping on pockets. The piping did do its job and it helped to curve the edges of the pockets and hold the curve in place as I stitched the pockets on.

Plus, it looks really cute and makes the pockets stand out from the rest of the jacket.

There is a lot more to say about the sewing of this jacket but I’m going to stop here and give you a break from the long list of lessons I was learning on this project. Stay tuned for the finale of this backwards jacket next time!

Until then, sew forth and fleece on!

Simplicity 2907 – Hong Kong Kitty – Part 3

DSCN0598A Hong Kong seam is made when you finish the edges of a seam by covering them with bias tape. It sounds simple enough to do, but there are always new sewing lessons to be learned every time you try something new and this time was no different.

But first a note to myself, make sure and cut the skirt pieces with a larger seam allowance to accommodate the bias tape. This gives you room to sew the bias tape on and not affect the circumference of the top of the skirt.

DSCN0570Two lessons that I learned about applying bias tape from the construction of this dress were to make sure and watch which side of the bias tape you’re working on and to watch which side of the fabric the bias tape is going to fold to.

DSCN0574Lesson one, remember the advise about making one side of the bias tape longer than the other while ironing the bias tape? And remember being careful to do just that as you ironed? Well, use that to your advantage when you’re sewing the bias tape on. When I started to sew the bias tape to my first seam allowance, I did not think to make sure I was sewing the shorter side of the bias tape first. By making sure that shorter side of the bias tape is sewn down first , that gives you the longer side to fold over. This gives you the little extra fabric on the back side, making it easier DSCN0575to catch the bias tape as you stitch in the ditch on the top side. When you stitch the longer side first and then fold the shorter side over, not only is there not the extra fabric but you are short fabric from folding over the longer side. Once I figured this out and sewed the short side first and then folding over the long side, the sewing on of the bias tape became much easier.

DSCN0577The second lesson of watching which side of the fabric the bias tape is folded to came when I added the the bias tape to the hem. When I sewed the bias tape to the seam allowances, I sewed it to the top of the fabric and then folded it to the back. After stitching in the ditch on the top, I had a nice clean finish on top and it did not matter if my seam was a little wavy on the back side. After binding the seam allowances of the two seams of the skirt, I had plenty of bias tape left over so I decided to use the remaining bias tape to finish off the hem of the skirt too.

DSCN0602But, since I did not remember to think a couple of steps ahead and see what was going to fold where, I sewed the short side of the bias tape to the inside of the hem. This meant I would be folding the longer side of the bias tape to the front of the skirt. Even though I had remembered to sew the short end first, I had not thought about what side the bias tape would be folding to. At this point when I stitched in the ditch on the inside of the skirt, the wavy part of the seam from catching the bias tape would be on the top side of the skirt in plain view. And the nice clean finish would be on the inside where no one could see it.

DSCN0601To fix this I could unpick the bias tape and sew it again, this time to the outside of the skirt and fold the bias tape to the inside. Rolling my eyes at the thought of unpicking all that bias tape, I thought of another plan. I would not finish the bias tape with a stitch in the ditch seam but sew a nice even edge on the top of the folded over bias tape. This way I would have a seam on the bias tape but it would not be wavy like the one I had sewn from the opposite side. The inside part would have the wavy seam instead. This worked out just great! My seam on the bias tape side is nice and smooth and even, but if you look inside you will see a seam that hits and misses the ditch between the bias tape and skirt. This is fine with me. It looks great on the outside and it still looks acceptable from the inside, and I did not have to unpick a single stitch.

DSCN0600Because I had attached the buttons and button holes while completing the bodice of this dress, the last step was to attach the skirt to the bodice. At this point I still had plenty of bias tape left so I decided to use it to finish this last seam attaching the skirt to the bodice too. Because this seam is inside the dress, I did not care which side had the clean finish and which side had the wavy seam, and using the bias tape did give the seam a nice beautiful finish. Note to myself – keep bias tape and Hong Kong seams in mind for finishing seams where a serged seam would be exposed.

DSCN0605This dress turned out so adorable once it was completed. I love the true camp collar and how much easier it was to sew than the collar the original pattern called for. With the changes that I made to this pattern, I will definitely be using this pattern again for future projects. I also love the Hong Kong seam of the skirt as well as the bias tape hem. I learned many sewing lessons from the construction of this dress, especially regarding the making of and the applying of bias tape. I hope some little girl will enjoy wearing it.

Until next time, sew forth and sew on.

Simplicity 2907 – Hong Kong Kitty – Part 2

DSCN0556When it came to making bias tape my first thought was just to purchase some, but then I stopped myself since I was supposed to be learning new sewing skills while making this project. Making bias tape was something I have never done before so now was a great time to learn.

The first step was to cut out strips of fabric on the bias. Since I had some white kitty fabric left, I decided to use it to make the bias tape with. I had no idea how much bias tape I needed for this project, but I had enough scraps to make 4 yards so that sounded like plenty. With the markings on my cutting table and my trusty metal ruler and my blade, it was easy to measure and cut the bias strips to the proper sizes.

DSCN0562Next came stitching the bias strips into one long piece. This took some thought. After thinking that I had the angles correct I sewed the pieces together, only to find out that I had not angled the strips correctly. A quick internet search taught me that the strips needed to be sewn at right angles. After learning how to sew them the right way, I unpicked and sewed the strips together correctly. The main thing I learned here that it is important to take the cutting of the strips seriously. Carefully cut strips out make it easier to sew the right angles.

DSCN0566Ironing the bias tape into its folded shape was the next step. Years ago, my mom gave me a bias tape maker. I promptly brought it home and tossed it in the closet with my other sewing notions. Now it was coming out of the closet and making its debut. It took a little bit of finagling to get the bias strip in the bias tape maker but once it was in, it was easy to see how the maker was going to fold the strip and make the forming and ironing of the bias tape DSCN0568easier.

 

While searching the internet on the angles, I did read that it was best to make one side of the bias tape larger than the other, not much, just enough to give you a little sewing edge. I decided to follow their advice. The ironing of the bias tape was time consuming but not difficult. Once again I learned that carefully cut strips and carefully sewn angles make it easier iron the folds. Accuracy is a key point of successful bias tape making.

In a short time, I had 4 yards of bias tape made and I was ready to start sewing the Hong Kong seams of the skirt.

Until then, sew forth on and bias on!

Simplicity 2907 – Hong Kong Kitty – Part 1

S2907 - Version 2After enjoying altering a pattern that I had previously made, I turned my attention back to Simplicity 2907. I like the design of this little girls dress with the camp shirt attached to the drop waist skirt. What I did not like about the pattern was the bodice of the shirt being cut for a stand collar and then a camp collar being attached. So, I either needed to alter this pattern and give it a stand collar or cut the front to make it an actual camp collar. The camp collar on the dress is much cuter than a stand collar would be so I chose to make the alterations to the front of bodice by adding a facing. But there was more to be learned from the making of this dress. I decided to use Hong Kong seams to finish the seams of the skirt and this lead to the making of bias tape. This would be two new sewing skills, Hong Kong seams and making bias tape, for me. But, I’m getting ahead of myself. Let’s start first with the alterations that I made.

DSCN0552The first steps were to select the fabric, alter the pattern, and cut the dress out. I knew I wanted to use up the kitty scraps from the wrap top I had made previously. And I wanted to make the front and back of bodice from the pink fabric and the sleeves and collar from the white, but that did not work out as I had hoped. As you may recall, the last time I made this dress, I used a thin yellow fabric for the bodice. After attaching the dropped waist skirt, I was afraid that the little girl’s panties would show through the yellow at the top of the skirt and I didn’t want to worry about that this time around. Using the pink for the front and the back would solve this, but DSCN0554I did not have enough scraps to do that. So, I picked the white for the front and the pink for the rest of the bodice pieces. At least the white kitty fabric is heavier than the yellow was so maybe there would not be a see through fabric problem with it. I found some scraps of denim in the stash for the skirt. I would not be lining the denim, so this would work great for the Hong Kong seams.

DSCN0604Altering the pattern was simple. I mirrored the front pattern piece to make an attached facing. Instead of the first steps in the sewing process being sewing the odd box shape and cutting the funny notch for the collar, I simply sewed a camp shirt top like I make for myself, with the folded over front facings to complete the bodice front, and a pieces of twill tape to complete the collar. I did not do Hong Kong seams on the bodice. I was saving those for the skirt. I was smart enough to make the buttonholes first before I attached the skirt so that there was no arguing with the bulk of the seam on the bottom buttonhole.

Soon enough, I had the bodice completed and it was time to sew the skirt. The first step would be to make bias tape. And that is a story for next time.

Until then, sew forth and camp collar on!